How to check and replace front wheel bearings on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

In most cases, the front wheel bearings should be checked whenever the front of the vehicle is raised, typically coinciding with brake pad replacement. The vehicle must be supported safely on jackstands and each wheel assessed by spinning it while checking for noise, rolling resistance and freeplay. You should grab the top and bottom of each tire to check for excessive play as you move the wheel in and out on the spindle; if there is any noticeable movement, bearing inspection, repacking with grease or replacement is required. After removing the wheel, remove the brake caliper and hang it out of your way possibly using a wood block between the brake pads for separation. Thereafter pry out dust cap, straighten and remove cotter pin then take off nut lock, nut, and washer from spindle. Slightly pull hub/disc assembly outwardly then push it back to facilitate removal of outer bearing. Then separate hub/disc assembly from spindle using screwdriver skimming seal out of rear side of hub keeping in mind how it was oriented during its installation. Proceed further to remove inner wheel bearing, clean all components thoroughly with solvent before carefully inspecting them for damage on races or bearings themselves. Replace any defective bearing races at a machine shop if necessary making sure that old bearings are not installed on new races. Thereafter pack bearings with high-temperature front wheel bearing grease and apply thin coat to designated spindle areas. Finger dam grease inboard of each bearing race inside the hub to contain excess grease. After this insert grease-packed inner bearing, a new seal then put outer bearing on top. Place washer on spindle followed by spindle nut which should be tightened gently; spin hub while tightening to approximately 20 ft-lbs then loosen 1/4-turn and finally secure snugly by hand using new cotter pin plus nut lock. Next install dust cap; replace brake caliper; re-attach the wheel then check condition of bearings by grabbing top & bottom of the tire. Finally, lower the vehicle.

How to replace the rear Wheel Bearing on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the axleshaft and oil seal, you will first need a bearing puller. Attach the puller to the slide hammer, the bearing can be extracted from the axle housing. After removing the bearing, the recess should be cleaned out. The new bearing can then be installed using a bearing installer or a piece of pipe against the outer bearing race. Ensure that the bearing is tapped in fully and that the numbers are visible from the outer end of the axle housing, and then install a new oil seal before reattaching the axleshaft.

Genuine Chevrolet S10 Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Wheel Bearings found

View related parts
Chevrolet S10 Rear Wheel Bearing
Part Number: 12479031
$46.59 MSRP: $92.44
You Save: $45.85 (50%)
ADD TO CART
Product Specifications
- Other Name: Bearing,Rear Wheel
- Position: Rear
- Replaces: 09442126, 9442126
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2003 Chevrolet S10 | PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 457052
$38.08 MSRP: $66.52
You Save: $28.44 (43%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Inner
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1995 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 457196
$23.79 MSRP: $43.24
You Save: $19.45 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Inner
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 26053326
$10.10 MSRP: $19.06
You Save: $8.96 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft; Axle Bearing, Bearing, Output Shaft Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 26041515
$27.08 MSRP: $51.10
You Save: $24.02 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft; Inner Pinion Bearing, Output Shaft Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Rear Wheel Bearing
Part Number: 88927028
$25.19 MSRP: $47.53
You Save: $22.34 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Rear Axle Shaft
- Position: Rear
- Replaces: 15595140
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2003 Chevrolet S10 | PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Wheel Bearing
Part Number: 14066918
$10.68 MSRP: $20.16
You Save: $9.48 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 457434
$10.48 MSRP: $27.74
You Save: $17.26 (63%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1983-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 12413045
$228.98 MSRP: $454.33
You Save: $225.35 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Kit,Front Wheel; Hub & Bearing
- Position: Front
- Replaces: 07470607, 19150096, 7470607
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Wheel Hub Kit, Front
Part Number: 7470013
$196.54 MSRP: $599.94
You Save: $403.40 (68%)
ADD TO CART
Product Specifications
- Other Name: Hub Kit,Front Wheel; Hub & Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1997 Chevrolet S10 | 2 DOOR, 4 DOOR, ELECTRIC, PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Hub
Part Number: 26041516
$4.46 MSRP: $8.42
You Save: $3.96 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Asm,Front Drive Axle Clutch Shaft; Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
- 1995 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Rear Wheel Bearing
Part Number: 12471606
$8.03 MSRP: $14.39
You Save: $6.36 (45%)
Product Specifications
- Other Name: Bearing,Rear Axle Shaft
- Position: Rear
- Replaces: 09428573, 07451785, 9428573, 7451785
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-2004 Chevrolet S10 | 2 DOOR, 4 DOOR, CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Wheel Bearing
Part Number: 26029615
Product Specifications
- Other Name: Bearing,Front Drive Axle Clutch Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1983-1996 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Wheel Hub
Part Number: 7470587
Product Specifications
- Other Name: Hub,Front Wheel; Hub & Bearing
- Replaces: 7466986
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Chevrolet S10 | ELECTRIC
View related parts
Chevrolet S10 Wheel Hub Kit, Front
Part Number: 7470005
Product Specifications
- Other Name: Hub Kit,Front Wheel; Front Hub, Front Hub & Bearing, Hub, Hub & Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1983-1993 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L

Chevrolet S10 Wheel Bearing

Chevrolet S10 vehicles have a component known as the Wheel Bearing, which assists the wheels in rotating freely and hence, is related to performance and safety. The hub and bearing assemblies are 3 variants, with the widespread unit assembly that contains the ABS sensor. If the bearings are loose or worn, there will be noise and vibration, which in turn may lead to a wheel coming off. The regularity of inspection and maintenance requirements is to inspect whether it is rough, has play or other damage. Replacement may be necessary, new races and high-quality grease should be used to maintain the correct operation. In summing up, the Wheel Bearing is needed for comfortable and risk-free driving of Chevrolet S10 automobiles.

Each OEM Chevrolet S10 Wheel Bearing we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Wheel Bearing Parts Questions & Experts Answers

Front Wheel Bearing
26053326
Q: How to check and replace front wheel bearings on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: In most cases, the front wheel bearings should be checked whenever the front of the vehicle is raised, typically coinciding with brake pad replacement. The vehicle must be supported safely on jackstands and each wheel assessed by spinning it while checking for noise, rolling resistance and freeplay. You should grab the top and bottom of each tire to check for excessive play as you move the wheel in and out on the spindle; if there is any noticeable movement, bearing inspection, repacking with grease or replacement is required. After removing the wheel, remove the brake caliper and hang it out of your way possibly using a wood block between the brake pads for separation. Thereafter pry out dust cap, straighten and remove cotter pin then take off nut lock, nut, and washer from spindle. Slightly pull hub/disc assembly outwardly then push it back to facilitate removal of outer bearing. Then separate hub/disc assembly from spindle using screwdriver skimming seal out of rear side of hub keeping in mind how it was oriented during its installation. Proceed further to remove inner wheel bearing, clean all components thoroughly with solvent before carefully inspecting them for damage on races or bearings themselves. Replace any defective bearing races at a machine shop if necessary making sure that old bearings are not installed on new races. Thereafter pack bearings with high-temperature front wheel bearing grease and apply thin coat to designated spindle areas. Finger dam grease inboard of each bearing race inside the hub to contain excess grease. After this insert grease-packed inner bearing, a new seal then put outer bearing on top. Place washer on spindle followed by spindle nut which should be tightened gently; spin hub while tightening to approximately 20 ft-lbs then loosen 1/4-turn and finally secure snugly by hand using new cotter pin plus nut lock. Next install dust cap; replace brake caliper; re-attach the wheel then check condition of bearings by grabbing top & bottom of the tire. Finally, lower the vehicle.
Rear Wheel Bearing
12471606
Q: How to replace the rear Wheel Bearing on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the axleshaft and oil seal, you will first need a bearing puller. Attach the puller to the slide hammer, the bearing can be extracted from the axle housing. After removing the bearing, the recess should be cleaned out. The new bearing can then be installed using a bearing installer or a piece of pipe against the outer bearing race. Ensure that the bearing is tapped in fully and that the numbers are visible from the outer end of the axle housing, and then install a new oil seal before reattaching the axleshaft.