My Garage
My Account
Cart
Genuine Chevrolet S10 Drive Shaft
Axle Shaft- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
63 Drive Shafts found
Chevrolet S10 Front Axle Propeller Shaft
Part Number: 94717722$655.96 MSRP: $891.48You Save: $235.52 (27%)Ships in 1-2 Business Days
Chevrolet S10 Propeller Shaft Assembly
Part Number: 15036997$145.05 MSRP: $466.17You Save: $321.12 (69%)Ships in 1-2 Business DaysChevrolet S10 Front Axle Propeller Shaft Assembly
Part Number: 15062956$336.32 MSRP: $812.88You Save: $476.56 (59%)Ships in 1-2 Business Days
Chevrolet S10 Rear Propeller Shaft
Part Number: 26030512$407.79 MSRP: $519.02You Save: $111.23 (22%)Ships in 1-2 Business Days
Chevrolet S10 Shaft Asm,Front & Rear Propeller
Part Number: 19201890$1332.29 MSRP: $1722.41You Save: $390.12 (23%)
| Page 1 of 4 |Next >
1-20 of 63 Results
Chevrolet S10 Drive Shaft Parts Questions & Experts Answers
- Q: How do you remove the rear driveshaft on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?A: To remove the rear driveshaft, start by disconnecting the negative cable from the battery. Then, raise the vehicle and support it securely on jackstands. Make marks on the driveshaft and the differential flange to ensure proper reinstallation. Remove the rear universal joint bolts and straps, and if applicable, remove the bolts, nuts, and washers from the companion flange. If the vehicle has a two-piece driveshaft, remove the bolts, nuts, and washers from the center support bearing bracket. Lower the rear of the driveshaft and slide the front out of the transmission or transfer case. If there is a splined yoke, cover it with a plastic bag to prevent fluid loss. If replacing the center support bearing, unscrew the collar, separate the driveshaft sections, and install the new bearing and collar. To install the driveshaft, clean the transmission or transfer case area, slide the front of the driveshaft in and connect the companion flange. Raise the rear of the driveshaft, align the marks, and install the straps and bolts. For the front driveshaft on 4WD models, raise the vehicle and remove the skid plate. Mark the relationship of the driveshaft to the front differential flange and, on 1994 models, the transfer case flange. Remove the bolts and straps from the differential flange and, on 1994 models, the transfer case flange. On 1994 models, separate the driveshaft at the transfer case flange and lower it. In 1995 and later models, drop down the front end of the driveshaft first and slide it off the transfer case splined output shaft. To install, attach the front end to the front differential flange and install the straps and bolts. Extend or compress the driveshaft as necessary and attach the rear end to the transfer case flange, tightening all bolts to the proper torque specifications.
- Q: What is a driveshaft and Universal Joint and its function in Chevrolet Blazer,S10,GMC Jimmy and Sonoma?A: A driveshaft is a tube or pair of tubes that transmits power between the transmission or transfer case on 4WD models and the Differential. It is equipped with universal joints at either end and in the center for two-piece driveshafts. On 2WD models, the driveshaft has a splined yoke at the front that allows it to slide back and forth within the transmission, with an oil seal to prevent fluid leakage and dirt entry. For 4WD models, the driveshaft may have a splined yoke or companion flange at the transfer case end, and two-piece driveshafts usually have a slip joint at the front of the rear section. Center bearings support the driveline in two-piece driveshafts, mounted in a rubber cushion on a frame crossmember. The driveshaft requires minimal service, with the universal joints being lubricated for life and replaced if problems arise. It is important to keep the driveshaft clean and inspect it for damage, ensuring the small weights used for balancing are in place and securely attached. Any noise or vibration while driving may indicate a problem with the driveshaft, which can be verified through a road test.
Related Chevrolet S10 Parts
Browse by Year
2004 Drive Shaft 2003 Drive Shaft 2002 Drive Shaft 2001 Drive Shaft 2000 Drive Shaft 1999 Drive Shaft 1998 Drive Shaft 1997 Drive Shaft 1996 Drive Shaft 1995 Drive Shaft 1994 Drive Shaft 1993 Drive Shaft 1992 Drive Shaft 1991 Drive Shaft 1990 Drive Shaft 1989 Drive Shaft 1988 Drive Shaft 1987 Drive Shaft 1986 Drive Shaft 1985 Drive Shaft 1984 Drive Shaft 1983 Drive Shaft 1982 Drive Shaft