My Garage
My Account
Cart
Genuine Chevrolet S10 Axle Shaft
Car Axle Shaft- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
43 Axle Shafts found
Chevrolet S10 Rear Axle Drive Shaft
Part Number: 26009534$338.14 MSRP: $450.77You Save: $112.63 (25%)Ships in 1-2 Business Days
Chevrolet S10 Rear Axle Drive Shaft
Part Number: 26064387$298.15 MSRP: $444.56You Save: $146.41 (33%)Ships in 1-2 Business Days
| Page 1 of 3 |Next >
1-20 of 43 Results
Chevrolet S10 Axle Shaft
The Axle Shaft of Chevrolet S10 vehicles is a rather significant part of its mechanical structure which transmits power from the differential to the wheels where the shaft is provided with philosophies that enables the wheels to rotate independently for purposes of boosting the traction. These steel shafts come in different forms; the solid axles for trucks and old rear-wheel drive cars and the half-shafts on cars with independent suspensions. Drives are referred to as a solid axles that have differential and axle shafts, on the other hand, halfshafts have splined shafts that are connected with CV Joints and wheel hubs. Boh, axle shafts may wear out by rubbing against the ground, and cause such problems as noise, vibration and others, while worn out seals will lead to loss of lubricating oil and contamination of the brake system. In general, Axle Shaft contributes to the support of weight load as well as the proper distribution of torque to Wheeler in Chevrolet S10 automobiles.
Each OEM Chevrolet S10 Axle Shaft we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet S10 Axle Shaft Parts Questions & Experts Answers
- Q: How do you remove the rear axle assembly on Chevrolet S10?A: To remove the rear axle assembly, begin by loosening the rear wheel lug nuts and lifting the rear of the vehicle with jackstands placed under the frame. Remove the rear wheels and position a jack under the rear axle differential case. Disconnect the driveshaft and secure it out of the way.
- Q: How do you remove the driveaxle on 4WD Chevrolet S10?A: To take out the axle shaft, start off by loosening the wheel lug nuts and raising the motorcar with jackstands. Remove the wheel and use a prybar or big screwdriver to hold the axle shaft while loosening the axle shaft hub nut using a big breaker bar. Get rid of the nut and washer. Then, keep hold of the axle shaft in position and clear away the axle shaft flange bolts ensuring you label CV joint inner to flange interconnectivity before eliminating these bolts. On 1999 on models, there are no axleshafts which are flanged to differential housing anymore but they have snap rings holding them at inside closed end of spline ends at trilobate joints. To free up an axleshaft, thump against it somewhere on its tripod container with wooden hammer until it snaps out of place from its groove. Take out steering knuckle then remove also halfshaft assembly. To reinstall proceed vice versa however when doing that ensure that you properly torque rear cv joint bolt and tighten front left outer cv joint as well as right outer cv joint hub nuts.
- Q: How do you remove the rear axle on Chevrolet S10?A: To start the process of removing the rear Differential, lift the rear of the vehicle and support it securely using jackstands. Take off the wheel as well as brake drum. If there is a locking differential on that vehicle, remove both rear wheels and brake drums. Remove the cover of your differential to let the oil drain into a pan. For traditional differentials, take out pinion shaft by extracting lock bolt. Using an assistant push in on an outer flanged end of an axle shaft while removing any c-lock from groove inside opposite end of a shaft. Turn over such a differential so that you can gain access and support its pinion shaft in order to avoid it falling down into case when working on locking type differentials. Partially withdraw your pinion shaft by taking out its lock bolt and rotating this type of differential until a shaft touches case allowing enough space for clearing out to c-locks. Use screwdriver for twisting c-lock until open endpoints are aligned then insert axleshaft back in then remove c-lock which is compressed at this time, repeat procedure with another axleshaft also with C-Lock no longer in place carefully pullout axleshaft because it may damage oil seal if not taken with great care some models may have a thrust washer in diff make sure it doesn't fall out when removing axle shaft next, take care inserting this part into housing so that it seats properly inside differential always used on typical differentials putting lock on flange must be used to achieve this result put C-Lock back into groove on axle shaft slide backwards using correct positioning after installing C-locks after withdrawing axleshafts slowly until C-Lock clears thrust block now that c-locks are installed push pinion shat through position where hole lines up with lock bold hole then install lock bolt at last install cover and fill diff with specified lubricants reinstalling brake drums and wheels followed by lowering car.
- Q: What is the type of rear axle assembly and differential used on Chevrolet S10?A: The rear axle assembly is a hypoid, semi-floating type with a Differential that allows the outer rear tire to turn more quickly than the inner tire when the vehicle goes around a corner. The axle shafts are splined to the differential side gears, causing the inner tire to turn more slowly than the outer tire. The differential pinion gears roll around the slower side gear, driving the outer side gear and tire more quickly. The differential is housed within a casting with a pressed steel cover known as the "carrier," and the steel axle tubes are pressed into and welded to the carrier. On 4WD models, a fully independent front axle assembly is used, consisting of a differential and a pair of driveaxles with inner and outer constant velocity (CV) joints. An extension axleshaft is employed on the right side to make up the difference in distance between the differential and the right front wheel. An optional locking limited-slip rear axle is also available, which allows for normal operation until one wheel loses traction. This differential includes a pair of clutch "cones" that slow the rotation of the differential case when one wheel is on a firm surface and the other on a slippery one, equalizing the rotation speed of the axleshaft driving the wheel with traction. It is important to check for other possible causes before assuming the axle is the problem, as road noise, tire noise, and engine and transmission noise can be mistaken for axle issues. Overhauling the differential may require special tools and is not typically cost-effective for a do-it-yourselfer.
Related Chevrolet S10 Parts
Chevrolet S10 Torque Converter
Chevrolet S10 Wheel Bearing
Chevrolet S10 Transmission Assembly
Chevrolet S10 Slip Yoke
Chevrolet S10 Transmission Pan
Chevrolet S10 Input Shaft Bearing
Chevrolet S10 Output Shaft Bearing
Chevrolet S10 Transmission Gasket
Chevrolet S10 Pinion Washer
Chevrolet S10 Transmission Oil Cooler
Browse by Year
2004 Axle Shaft 2003 Axle Shaft 2002 Axle Shaft 2001 Axle Shaft 2000 Axle Shaft 1999 Axle Shaft 1998 Axle Shaft 1997 Axle Shaft 1996 Axle Shaft 1995 Axle Shaft 1994 Axle Shaft 1993 Axle Shaft 1992 Axle Shaft 1991 Axle Shaft 1990 Axle Shaft 1989 Axle Shaft 1988 Axle Shaft 1987 Axle Shaft 1986 Axle Shaft 1985 Axle Shaft 1984 Axle Shaft 1983 Axle Shaft 1982 Axle Shaft