What is the location and removal process for the MAP sensor on Chevrolet Impala and Monte Carlo?

The V6 models have their MAP sensor on top and at the left rear corner of the intake manifold. To remove the MAP sensor from an intake manifold on a V6 engine, first, disconnect the electrical connector, then remove the retaining bolt and hold-down clamp. Then lift it straight up. The next step is to remove the bolts that hold down the MAP sensor in place and take out the MAP sensor. You should get rid of the old MAP sensor sealing grommet after removing it from its position. If this is not done, it should be replaced if it has got cracks, tears or other signs of wear off. While mounting a new one, one must smear some oil on it so that when pushing into its hole, it will go smoothly without tearing apart easily. Putting back is vice versa of removal. On V8 models, you can find the MAP sensor fixing over the throttle body on top of the intake manifold. The first thing is to uncover an engine part. Afterward, pry up on a locking tab which connected this device with wire harness of an automobile until it unlocks, and then pull it from above while shaking sideway (up and down). Finally pull directly out to detach them from their fixings as well as removing them out completely but slowly & carefully to prevent any possible damages from happening during process followed by:-Take away as well as inspect former sealing grommet relating towards MAP sensors since when they fall into wrong hands this could lead to problems;-If there is any damage noted like cracks for instance then just repair whatever has been torn or broken;-Ensure oiling is done gently but thoroughly by one who needs installation process smoothly because he would never wish see his new fittings become destroyed hence having difficulties making them fit well enough rather than always pulling them apart repeatedly forcing everything back together time after again until each part fits exactly how expected this may happen upon removal.

Genuine Chevrolet Impala MAP Sensor

Manifold Air Pressure Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 MAP Sensors found

View related parts
Chevrolet Impala Sensor,Map
Part Number: 12569240
$61.84 MSRP: $122.71
You Save: $60.87 (50%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Computer Control Sensors
- Replaces: 16254719, 16137039
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Chevrolet Impala | IMPALA, LS, LUMINA, POLICE CAR, SS | 6 Cyl 3.4L
- 1994-1996 Chevrolet Impala | CLASSIC 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR | 8 Cyl 5.7L
- 1985 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON | 6 Cyl 4.3L, 8 Cyl 5.7L Diesel
View More
View related parts
Chevrolet Impala Sensor Asm,Map
Part Number: 12219931
$47.97 MSRP: $154.32
You Save: $106.35 (69%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Computer Control Sensors; M.A.P. Sensor, Map Sensor, Pressure Sensor, Sensor
- Replaces: 16006833, 16006835
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 8 Cyl 5.0L
View related parts
Chevrolet Impala Sensor Assembly, Map
Part Number: 55573248
$30.02 MSRP: $56.65
You Save: $26.63 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Computer Control Sensors
- Replaces: 12591290, 93192107
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2020 Chevrolet Impala | LS, LS 4 DOOR NOTCHBACK, LS POLICE CAR, LT, LT 3.5, LT 4 DOOR NOTCHBACK, LTZ, LTZ 4 DOOR NOTCHBACK, SS | 4 Cyl 2.4L, 4 Cyl 2.5L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.6L, 6 Cyl 3.9L Flex, 8 Cyl 5.3L
View related parts
Chevrolet Impala Sensor Assembly, Manifold Differential Pressure
Part Number: 16231141
$31.90 MSRP: $102.62
You Save: $70.72 (69%)
ADD TO CART
Product Specifications
- Other Name: SENSOR
- Replaces: 16054920, 16006834
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Chevrolet Impala | 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 8 Cyl 4.4L, 8 Cyl 5.0L
View related parts
Chevrolet Impala SENSOR ASM,MAP
Part Number: 19418808
$72.39 MSRP: $143.62
You Save: $71.23 (50%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: M.A.P. Sensor, Map Sensor, Valve Assembly
- Replaces: 16249939, 09359409, 12614973, 16187556, 9359409
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | IMPALA, LS, LT, LUMINA, POLICE CAR, SS | 6 Cyl 3.8L
View related parts
Chevrolet Impala SENSOR ASM,MAP
Part Number: 19418807
$74.35 MSRP: $147.51
You Save: $73.16 (50%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: M.A.P. Sensor, Map Sensor
- Replaces: 12614970, 16212460
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Impala | LS, LT, SS | 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Impala SENSOR ASM,MAP
Part Number: 19418810
$68.77 MSRP: $142.80
You Save: $74.03 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 09350899, 12580698, 12615136, 9350899
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.8L
View related parts
Chevrolet Impala Sensor Assembly, Supercharge Air Inlet Pressure
Part Number: 12615135
$48.92 MSRP: $157.51
You Save: $108.59 (69%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Computer Control Sensors; M.A.P. Sensor, Map Sensor, Pressure Sensor
- Replaces: 12581167
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Impala | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L

Chevrolet Impala MAP Sensor

Absolutely speaking, MAP Sensor in Chevrolet Impala is one of the most important devices which is used to measure the positive air pressure entering into the intake manifold so that the engine control unit or ECU can position the device of fuel injection in right way. The primary function of the MAP Sensor mainly applies to the fuel injected engines and especially in the speed-density method by acting a key component in the determination of the air-fuel mixture in the combustion chamber. While naturally aspirated engines you will either find a MAP or MAF sensor, forced induction engines always incorporate both. MAP Sensor also plays a role in on board diagnostics as well as exhaust gas recirculation valve, this component is vital in giving measurements that will enable the right fuel flow to be metered and the engine performance tuned accordingly.

Each OEM Chevrolet Impala MAP Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Impala MAP Sensor Parts Questions & Experts Answers

Sensor Assembly, Map
55573248
Q: What is the location and removal process for the MAP sensor on Chevrolet Impala and Monte Carlo?
A: The V6 models have their MAP sensor on top and at the left rear corner of the intake manifold. To remove the MAP sensor from an intake manifold on a V6 engine, first, disconnect the electrical connector, then remove the retaining bolt and hold-down clamp. Then lift it straight up. The next step is to remove the bolts that hold down the MAP sensor in place and take out the MAP sensor. You should get rid of the old MAP sensor sealing grommet after removing it from its position. If this is not done, it should be replaced if it has got cracks, tears or other signs of wear off. While mounting a new one, one must smear some oil on it so that when pushing into its hole, it will go smoothly without tearing apart easily. Putting back is vice versa of removal. On V8 models, you can find the MAP sensor fixing over the throttle body on top of the intake manifold. The first thing is to uncover an engine part. Afterward, pry up on a locking tab which connected this device with wire harness of an automobile until it unlocks, and then pull it from above while shaking sideway (up and down). Finally pull directly out to detach them from their fixings as well as removing them out completely but slowly & carefully to prevent any possible damages from happening during process followed by:-Take away as well as inspect former sealing grommet relating towards MAP sensors since when they fall into wrong hands this could lead to problems;-If there is any damage noted like cracks for instance then just repair whatever has been torn or broken;-Ensure oiling is done gently but thoroughly by one who needs installation process smoothly because he would never wish see his new fittings become destroyed hence having difficulties making them fit well enough rather than always pulling them apart repeatedly forcing everything back together time after again until each part fits exactly how expected this may happen upon removal.