How do you remove and reinstall the transmission and flywheel on Chevrolet Corvette?

If you want to eliminate the transmission then initial starting examine series for example oil seals and in the event that they are damaged then replace then. In the models with a manual transmission, change or check the clutch or, where necessary, its elements and the release bearings. However, when tilting down the rear of the driveline, enough space should be provided between the engine and the instrument panel, so as to support the engine to avoid damage. Manual transmission models imply the flywheel to be fixed back in its previous position without the locating pin; to facilitate this, manufacturers put alignment marks. To remove the flywheel/driveplate bolts you need to lock the flywheel/driveplate from rotating you can use any available transmission mounting bolt and screwdriver. All should be replaced once removed because of the severity of stresses that are required of bolts. Do not disassemble the driveplate assembly on automatic models; it is pre-balanced as a part of the whole assembly. To disassemble the system, it is necessary to take out the retainer and flywheel, and note its weight before that. Remove the flywheel for cleaning and look for signs of damage, and also to examine the seating surfaces with the crankshaft, replace any oil sealing that has developed leaks. Again with the flywheel off you should clean the inboard face and the crankshaft speed/position sensor. When installing the flywheel/driveplate, fit the flywheel/driveplate on the crankshaft with the marks made during flywheel/driveplate removal aligned and then tightened with new bolts tightened in a diagonal sequence to the torque specified in the Toyota service manual. The installation process is the reverse of the removal process that has been explained above.

Genuine Chevrolet Corvette Flywheel

Clutch Flywheel

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Flywheels found

View related parts
Chevrolet Corvette Automatic Transmission Flexible Plate Assembly
Part Number: 12654640
$124.19 MSRP: $216.13
You Save: $91.94 (43%)
ADD TO CART
Product Specifications
- Other Name: Plate Assembly, Automatic Transmission Flexible ; Plate, Engine Crankshaft; Drive Plate, Flywheel
- Replaces: 12553054, 12602448, 12606620, 12637677, 12563136, 12580709
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L
- 2002-2003 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Engine Crankshaft FLYWHEEL
Part Number: 14088765
$120.71 MSRP: $210.09
You Save: $89.38 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel, Engine Crankshaft; Drive Plate
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1996 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Engine Crankshaft FLYWHEEL
Part Number: 12571611
$320.57 MSRP: $530.56
You Save: $209.99 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Asm ; Flywheel, Engine Crankshaft; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Flywheels & Flexplates
Part Number: 24287452
$731.11 MSRP: $1160.77
You Save: $429.66 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Asm; Flywheel
- Replaces: 24255997
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Flywheels & Flexplates
Part Number: 24287451
$928.06 MSRP: $1473.46
You Save: $545.40 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Flywheel Asm; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Automatic Transmission Flexible Plate Assembly (W/ Hub)
Part Number: 12582437
$228.34 MSRP: $360.75
You Save: $132.41 (37%)
Product Specifications
- Other Name: Plate Assembly, Automatic Transmission Flexible (W/ Hub) ; Plate, Engine Crankshaft; Drive Plate
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L, 8 Cyl 6.0L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette Engine Crankshaft FLYWHEEL
Part Number: 12598613
$247.76 MSRP: $391.60
You Save: $143.84 (37%)
Product Specifications
- Other Name: Flywheel Asm ; Flywheel, Engine Crankshaft; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Clutch Flywheel
Part Number: 12570806
Product Specifications
- Other Name: Flywheel,(W/Clutch Pressure Plate); Flywheel, Pressure Plate
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Flywheel Assembly, (W/ Clutch Pressure Plate)
Part Number: 12581650
Product Specifications
- Other Name: Flywheel, Pressure Plate
- Replaces: 12561077, 12570281, 12562609, 12559868, 12562765, 12572731
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet Corvette | 2 DOOR, CONVERTIBLE, NOTCHBACK | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Engine Crankshaft FLYWHEEL
Part Number: 14085720
Product Specifications
- Other Name: Flywheel, Engine Crankshaft; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Flywheel Assembly
Part Number: 10174482
Product Specifications
- Other Name: Flywheel Asm; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1996 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L
View related parts
Chevrolet Corvette Flywheel Assembly
Part Number: 10174481
Product Specifications
- Other Name: Flywheel Asm; Flywheel
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1995 Chevrolet Corvette | 2 DOOR, CONVERTIBLE | 8 Cyl 5.7L

Chevrolet Corvette Flywheel

Each OEM Chevrolet Corvette Flywheel we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Corvette Flywheel Parts Questions & Experts Answers

Engine Crankshaft FLYWHEEL
12571611
Q: How do you remove and reinstall the transmission and flywheel on Chevrolet Corvette?
A: If you want to eliminate the transmission then initial starting examine series for example oil seals and in the event that they are damaged then replace then. In the models with a manual transmission, change or check the clutch or, where necessary, its elements and the release bearings. However, when tilting down the rear of the driveline, enough space should be provided between the engine and the instrument panel, so as to support the engine to avoid damage. Manual transmission models imply the flywheel to be fixed back in its previous position without the locating pin; to facilitate this, manufacturers put alignment marks. To remove the flywheel/driveplate bolts you need to lock the flywheel/driveplate from rotating you can use any available transmission mounting bolt and screwdriver. All should be replaced once removed because of the severity of stresses that are required of bolts. Do not disassemble the driveplate assembly on automatic models; it is pre-balanced as a part of the whole assembly. To disassemble the system, it is necessary to take out the retainer and flywheel, and note its weight before that. Remove the flywheel for cleaning and look for signs of damage, and also to examine the seating surfaces with the crankshaft, replace any oil sealing that has developed leaks. Again with the flywheel off you should clean the inboard face and the crankshaft speed/position sensor. When installing the flywheel/driveplate, fit the flywheel/driveplate on the crankshaft with the marks made during flywheel/driveplate removal aligned and then tightened with new bolts tightened in a diagonal sequence to the torque specified in the Toyota service manual. The installation process is the reverse of the removal process that has been explained above.