How do you remove and install the driveaxle on Chevrolet Corvette?

To remove the driveaxle, block the front wheels to prevent rolling, loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jackstands before removing the wheels. For 2012 and later models, unstake the driveaxle/hub nut using a punch or small chisel before loosening it, ensuring not to use air tools for this process. For vehicles without ceramic brake discs, install a punch or drift inside the brake disc vanes, rotate the wheel until it contacts the caliper bracket, and apply the parking brake to hold the wheel in place while loosening the driveaxle/hub nut. If equipped with ceramic brake discs, apply the parking brake and have an assistant depress the brake pedal firmly while loosening the nut. Unscrew the driveaxle/hub nut with a socket and large breaker bar, discard the old nut, and release the parking brake. To loosen the driveaxle from the hub splines, tap the end with a soft-faced hammer, and if it is stuck, use a hub puller to break it loose. For 2008 and earlier models, disconnect the ABS wheel speed sensor, electronic suspension control sensor link, outer tie-rod end, and parking brake cable, securing the cable out of the way. Use a floor jack to separate the upper control arm ball joint from the knuckle, rotate the knuckle outward to remove the driveaxle from the hub, and carefully pry the inner end out of the differential. For 2009 and later models, remove the rear knuckle and then pry the inner end of the driveaxle out of the differential. For installation, apply a light film of grease to the inner CV joint stub shaft where the seal rides, insert the splined end into the differential ensuring the spring clip locks in place, and grease the outer CV joint splines and knuckle before inserting the outer end into the hub. The remainder of the installation follows the reverse order of removal, including installing a new driveaxle/hub nut and tightening it to the specified torque, staking the collar of the nut into the driveaxle groove for 2012 and later models. Finally, check the differential lubricant level if any fluid leaked during removal, and install the wheel and lug nuts before lowering the vehicle and tightening the lug nuts to the specified torque.

Genuine Chevrolet Corvette Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 Axle Shafts found

View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly (RH Proc)
Part Number: 22873444
$222.87 MSRP: $387.90
You Save: $165.03 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint (Rh Proc) ; Shaft, Rear Axle Drive; Axle Assembly
- Position: Rear Passenger Side
- Replaces: 15851726, 10350598, 22762284, 25941373
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Rear Wheel Drive Shaft Assembly
Part Number: 84228346
$221.05 MSRP: $384.72
You Save: $163.67 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive ; Shaft Assembly, Rr Whl Drv; Axle Assembly
- Position: Rear
- Replaces: 23301165
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly
Part Number: 20977318
$596.33 MSRP: $803.69
You Save: $207.36 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint; Axle Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Gear Axle Shaft (Elsd, Lh, Output)
Part Number: 19302560
$119.83 MSRP: $170.70
You Save: $50.87 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft,Rear Axle (Elsd, Lh, Output)
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly
Part Number: 23301162
$245.82 MSRP: $427.84
You Save: $182.02 (43%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint; Axle Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2019 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly
Part Number: 25941372
$404.06 MSRP: $703.26
You Save: $299.20 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint ; Shaft, Rear Axle Drive; Axle Assembly
- Position: Rear
- Replaces: 15891870, 15874726
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Corvette | 2 DOOR, 2 DOOR SPECIAL, CONVERTIBLE | 8 Cyl 6.0L, 8 Cyl 6.2L, 8 Cyl 7.0L
View related parts
Chevrolet Corvette Shaft Assembly, Rear Whl Drv
Part Number: 85113611
$271.31 MSRP: $428.82
You Save: $157.51 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rr Whl Drv; Axle Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette Shaft Assembly, Rear Whl Drv Ujt (Rh Proc)
Part Number: 23435870
$233.67 MSRP: $369.32
You Save: $135.65 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Rear Passenger Side
- Replaced by: 85642686
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly (RH Proc)
Part Number: 20977317
$400.00 MSRP: $575.22
You Save: $175.22 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint (Rh Proc); Axle Assembly
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Shaft Assembly, R/Axl (Right) Mlsd
Part Number: 24299312
$228.15 MSRP: $360.60
You Save: $132.45 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Shaft Assembly, R/Axl (Left) (Elsd)
Part Number: 24299320
$356.87 MSRP: $564.03
You Save: $207.16 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE, Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette SHAFT ASM-RR WHL DRV
Part Number: 85642686
$233.67 MSRP: $369.32
You Save: $135.65 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Replaces: 23435870, 84686156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | STINGRAY CONVERTIBLE, STINGRAY COUPE, Stingray Convertible, Stingray Coupe | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette Shaft Assembly, R/Axl (Left) (Mlsd)
Part Number: 24299319
$337.31 MSRP: $533.13
You Save: $195.82 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | Stingray Convertible, STINGRAY CONVERTIBLE, Stingray Coupe, STINGRAY COUPE | 8 Cyl 6.2L
View related parts
Chevrolet Corvette SHAFT ASM-FRT WHL DRV HALF
Part Number: 86517684
$157.07 MSRP: $248.24
You Save: $91.17 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette SHAFT ASM-FRT WHL DRV HALF
Part Number: 86517685
$157.07 MSRP: $248.24
You Save: $91.17 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette SHAFT ASM-RR WHL DRV
Part Number: 85597888
$272.84 MSRP: $431.24
You Save: $158.40 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE, LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette SHAFT ASM-R/AXL (RIGHT)
Part Number: 24048639
$280.87 MSRP: $443.93
You Save: $163.06 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Passenger Side
- Replaced by: 24059051
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L
View related parts
Chevrolet Corvette SHAFT ASM-RR WHL DRV
Part Number: 85597887
$320.77 MSRP: $506.96
You Save: $186.19 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | LT2 AWD CONVERTIBLE, LT2 AWD COUPE, LT6 CONVERTIBLE, LT6 COUPE | 8 Cyl 5.5L, 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Wheel Drive Universal Joint Shaft Assembly
Part Number: 20977316
$304.01 MSRP: $480.49
You Save: $176.48 (37%)
Product Specifications
- Other Name: Shaft Assembly, Rear Wheel Drive Universal Joint; Axle Assembly
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE, Z06 2 DOOR CONVERTIBLE, Z06 2 DOOR PLAINBACK | 8 Cyl 6.2L
View related parts
Chevrolet Corvette Rear Gear Axle Shaft (Elsd,Lh,Output)
Part Number: 19302457
$95.61 MSRP: $150.45
You Save: $54.84 (37%)
Product Specifications
- Other Name: Shaft,Rear Axle (Elsd,Lh,Output)
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Corvette | 2 DOOR, 2 DOOR CONVERTIBLE | 8 Cyl 6.2L

| Page 1 of 2 |Next >

1-20 of 34 Results

Chevrolet Corvette Axle Shaft

The Axle Shaft in Chevrolet Corvette vehicles is an important component that transmits power from the differential to the wheel that in turns can rotate independently. This design helps to have good grip when cornering through allowing the wheels to rotate in different speeds. Chevrolet Corvette Axle Shafts, as can be expected, are usually made of high tensile materials such as chrome-molybdenum or carbon steel because of the horsepower and torque generated by the car. The uses of Axle Shafts in Chevrolet Corvette is as follows Live axle is used for weight support and the drive axles used in Chevroleum Corvette is with differential both for front and rear wheel drive system. The main disparity within these types is based upon physical characteristics for example split axles for independent suspensions which make the car more comfortable to ride in than a normal straight axle. In one way or another, the Axle Shaft plays a big role in the operation of the Chevrolet Corvette especially in terms of performance and handling.

Each OEM Chevrolet Corvette Axle Shaft we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Corvette Axle Shaft Parts Questions & Experts Answers

Rear Wheel Drive Universal Joint Shaft Assembly (RH Proc)
22873444
Q: How do you remove and install the driveaxle on Chevrolet Corvette?
A: To remove the driveaxle, block the front wheels to prevent rolling, loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jackstands before removing the wheels. For 2012 and later models, unstake the driveaxle/hub nut using a punch or small chisel before loosening it, ensuring not to use air tools for this process. For vehicles without ceramic brake discs, install a punch or drift inside the brake disc vanes, rotate the wheel until it contacts the caliper bracket, and apply the parking brake to hold the wheel in place while loosening the driveaxle/hub nut. If equipped with ceramic brake discs, apply the parking brake and have an assistant depress the brake pedal firmly while loosening the nut. Unscrew the driveaxle/hub nut with a socket and large breaker bar, discard the old nut, and release the parking brake. To loosen the driveaxle from the hub splines, tap the end with a soft-faced hammer, and if it is stuck, use a hub puller to break it loose. For 2008 and earlier models, disconnect the ABS wheel speed sensor, electronic suspension control sensor link, outer tie-rod end, and parking brake cable, securing the cable out of the way. Use a floor jack to separate the upper control arm ball joint from the knuckle, rotate the knuckle outward to remove the driveaxle from the hub, and carefully pry the inner end out of the Differential. For 2009 and later models, remove the rear knuckle and then pry the inner end of the driveaxle out of the differential. For installation, apply a light film of grease to the inner CV joint stub shaft where the seal rides, insert the splined end into the differential ensuring the spring clip locks in place, and grease the outer CV joint splines and knuckle before inserting the outer end into the hub. The remainder of the installation follows the reverse order of removal, including installing a new driveaxle/hub nut and tightening it to the specified torque, staking the collar of the nut into the driveaxle groove for 2012 and later models. Finally, check the differential lubricant level if any fluid leaked during removal, and install the wheel and lug nuts before lowering the vehicle and tightening the lug nuts to the specified torque.