How is the ignition switch removed and installed on Chevrolet Caprice?

As a precaution against theft of the vehicle, the ignition switch is located inside the channel section of the brake pedal support and is remotely controlled by a rod and rack assembly from the ignition lock cylinder. To remove the ignition switch, the steering column must either be removed or lowered and well supported, without the need to remove the steering wheel. Before removing the switch, which is secured by two screws, it should be set to the 'LOCK' position. If the lock cylinder and actuating rod have already been removed, the 'LOCK' position can be determined by inserting a screwdriver in the actuating rod slot, moving the switch slide up until a definite stop is felt, and then moving it down one detent. Installation is a reversal of removal, ensuring the switch is in the 'LOCK' position and using original or identical type securing screws, as longer or thicker screws could render the collapsible design of the steering column inoperative. For models from 1977 to 1981, the switch should be set to the 'OFF-UNLOCKED' position before removal. If the lock cylinder has already been removed, the switch actuating rod should be pulled up until a definite stop is felt and then pushed down two detents. Before installing the switch, it should be set to the 'OFF-UNLOCK' position with the gearshift lever in neutral. This involves moving the switch slider two positions to the right from 'ACCESSORY' to 'OFF/UNLOCK', fitting the actuator rod into the slider hole, and assembling it to the steering column using two screws, with only the lower one tightened to 35 in-lb torque.

Genuine Chevrolet Caprice Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Ignition Switches found

View related parts
Chevrolet Caprice Switch,Ignition & Start
Part Number: 1990116
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Caprice | 4 DOOR, CLASSIC 4 DOOR, CLASSIC LS 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR, STATION WAGON | 6 Cyl 4.3L, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L
- 1982-1988 Chevrolet Caprice | 4 DOOR, BROUGHAM 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.3L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Caprice Switch,Steering Column Ignition
Part Number: 1990115
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1991 Chevrolet Caprice | 4 DOOR, BROUGHAM 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.3L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Caprice Switch,Ignition
Part Number: 26036235
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Caprice | CLASSIC 4 DOOR, CLASSIC STATION WAGON | 8 Cyl 4.3L, 8 Cyl 5.7L
View related parts
Chevrolet Caprice Switch,Ignition Key Alarm
Part Number: 26022717
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Caprice | 4 DOOR, CLASSIC 4 DOOR, CLASSIC LS 4 DOOR, CLASSIC STATION WAGON, LS 4 DOOR, STATION WAGON | 6 Cyl 4.3L, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L
- 1982-1988 Chevrolet Caprice | 4 DOOR, BROUGHAM 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.3L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel
View related parts
Chevrolet Caprice Switch Assembly, Ignition Key Warning Alarm
Part Number: 7804414
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1991 Chevrolet Caprice | 4 DOOR, BROUGHAM 4 DOOR, CLASSIC 2 DOOR, CLASSIC 4 DOOR, CLASSIC STATION WAGON, STATION WAGON | 6 Cyl 3.8L, 6 Cyl 4.3L, 8 Cyl 4.4L, 8 Cyl 5.0L, 8 Cyl 5.7L, 8 Cyl 5.7L Diesel

Chevrolet Caprice Ignition Switch

The Ignition Switch is a very important part found in Chevrolet Caprice which works together with the ignition and charging system with the main functions of starting the car engine and regulating various parts like the radio and the power windows among others. With a help of a key or button or remote control, the computer of the car sets the starter solenoid and ignition elements that are required to start the motor. Year to year Chevrolet Caprice models had different kind of ignition switch in their design, and this car is basically uses mechanical key to switch on the ignition. Contemporary models may only require a push button while at the same time retaining the requirement of a transponder signal for security purposes. The basic form, however, is relatively consistent although advances seen in the field of technology have resulted in slight deviations from the original design structure, where some features such as the use of immobilisers have been added to the car to improve on its security.

Each OEM Chevrolet Caprice Ignition Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Caprice Ignition Switch Parts Questions & Experts Answers

Switch,Ignition Key Alarm
26022717
Q: How is the ignition switch removed and installed on Chevrolet Caprice?
A: As a precaution against theft of the vehicle, the ignition switch is located inside the channel section of the brake pedal support and is remotely controlled by a rod and rack assembly from the Ignition Lock Cylinder. To remove the ignition switch, the steering column must either be removed or lowered and well supported, without the need to remove the steering wheel. Before removing the switch, which is secured by two screws, it should be set to the 'LOCK' position. If the lock cylinder and actuating rod have already been removed, the 'LOCK' position can be determined by inserting a screwdriver in the actuating rod slot, moving the switch slide up until a definite stop is felt, and then moving it down one detent. Installation is a reversal of removal, ensuring the switch is in the 'LOCK' position and using original or identical type securing screws, as longer or thicker screws could render the collapsible design of the steering column inoperative. For models from 1977 to 1981, the switch should be set to the 'OFF-UNLOCKED' position before removal. If the lock cylinder has already been removed, the switch actuating rod should be pulled up until a definite stop is felt and then pushed down two detents. Before installing the switch, it should be set to the 'OFF-UNLOCK' position with the gearshift lever in neutral. This involves moving the switch slider two positions to the right from 'ACCESSORY' to 'OFF/UNLOCK', fitting the actuator rod into the slider hole, and assembling it to the steering column using two screws, with only the lower one tightened to 35 in-lb torque.