My Garage
My Account
Cart
Genuine Chevrolet C1500 Ignition Coil
Ignition Coil Resistor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Ignition Coils found
Chevrolet C1500 Distributor Ignition Pickup
Part Number: 10495089$26.43 MSRP: $49.86You Save: $23.43 (47%)Ships in 1-3 Business Days
Chevrolet C1500 COIL ASM,IGN
Part Number: 19418996$73.64 MSRP: $154.70You Save: $81.06 (53%)Ships in 1-3 Business Days
Chevrolet C1500 COIL KIT,IGN
Part Number: 19418995$38.60 MSRP: $109.38You Save: $70.78 (65%)Ships in 1-2 Business Days
Chevrolet C1500 Ignition Coil
Chevrolet C1500 Ignition Coil is one of the major parts that have a very important function of delivering sparks to the vehicle's ignition. Thus, the ignition coil being Voltage conversion part increase the voltage from battery's low voltage to high voltage to produce spark capable of igniting the air/fuel mixture in the cylinders. This process consists of the primary and secondary coils of insulated copper wire; these coils are wrapped around an iron core contained in a housing. The first circuit, known as the primary circuit links to the battery and charging circuit, while the second circuit, the secondary circuit features a high tension lead, distributor cap as well as spark plug's wires. Some of the Chevrolet C1500 vehicles have applied distributor ignition system, coil on plug system, wasted spark system and the like ignition coils have also been used in such cars. Ignition coil as a component is very sensitive to the performance of the vehicle and its failure can cause problems such as poor acceleration, poor fuel efficiency and rough idle among others, thus this is important to monitor it.
Each OEM Chevrolet C1500 Ignition Coil we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet C1500 Ignition Coil Parts Questions & Experts Answers
- Q: How to replace the Ignition Coil for Chevrolet C1500 and K1500?A: To disconnect the cable from the negative terminal of a battery, detach first if not done earlier the high tension lead of the coil and primary wire connector. Then remove mounting fasteners to separate coil from engine. For 1996 through 2000 models, take away electrical connectors from ignition coil and Ignition Control Module, and unplug coil wire from high-tension terminal. Remove ignition coil/module bracket mounting bolts and pull assembly out through engine. On a workbench, drill center of rivets holding coil to bracket, punch out rivets and remove coil off bracket. Screw new screws into bracket while retaining it with ignition coil. Finally put assembly back on engine and connect electrical connectors as well as fit in the wires into their respective terminals in the coil.
- Q: How to remove and install a distributor and pick-up coil for Chevrolet C1500 and K1500?A: Disconnect the cable from the negative battery terminal. Caution: On models equipped with the Theftlock audio system, be sure the lockout feature is turned off before performing any procedure which requires disconnecting the battery. Remove the Distributor cap and rotor. Remove the distributor from the engine. Detach the ignition coil leads from the module. Mark the distributor shaft and gear so they can be reassembled in the same relationship. Carefully mount the distributor in a vise equipped with soft jaws and, using a hammer and punch, remove the roll pin from the distributor shaft and gear. Pull out the distributor shaft. To remove the ignition coil, mount the distributor shaft in a vise equipped with soft jaws and, using a pin punch and hammer, knock out the roll pin. Remove the driven gear and spacer washers or springs from the end of the shaft-be sure to note their installed order. Remove the shaft from the distributor. To detach the ignition coil, remove the retaining clip. Lift the ignition coil assembly straight up and detach it from the distributor. Installation is the reverse of removal.
