Pontiac 13584872 Lift Gate Latch Assembly

You can Select Your Vehicle to check if 13584872 fits your vehicle.

Open the trunk lid/liftgate. Remove the pushpins securing the trunk lid liner, or remove the liftgate trim panel. Disconnect the electrical connector from the Trunk Latch assembly and the rod to the Trunk Lock Cylinder, if equipped. Remove the bolts securing the latch to the lid or liftgate. Remove the Trunk Latch assembly. Installation is the reverse of removal. Remove the pushpins securing the trunk lid liner. Disconnect the Trunk Lock Cylinder actuating rod. Remove the Trunk Lock Cylinder retaining clip. Remove the Trunk Lock Cylinder from the trunk lid. Installation is the reverse of removal.

To work on the front door, start by raising the window and then removing the door trim panel and watershield. For Cobalt/GS and ION models, disconnect the rod from the latch mechanism to the outside door handle and any electrical connectors from the door latch assembly, if applicable. Remove the latch mounting bolts and the inside handle retaining screw on ION models, and take out the handle, cable/rods, and latch as an assembly from the door. For lock cylinder and outer door handle replacement, follow specific steps for each model type. On Cobalt/GS models, remove the bolt securing the front of the handle from inside the door, then disconnect the lock cylinder rod and remove the lock cylinder mounting screws. On ION models, disconnect the lock cylinder rod and remove the lock cylinder from the door. For outer door handle replacement, lift up the handle and remove the plastic pushpin, then push the door handle towards the front of the vehicle to remove it from the pivot assembly in the door. For HHR models, remove the trim cap for the outside handle retaining screw, remove the screw, pull the door handle outwards, and remove the handle cover. To disengage the outside door handle lever from the handle reinforcement inside the door, pull it out of the door and to the rear. Inspect and replace the outside door handle seals if necessary. For the inside door handle, disconnect the actuator cable and reverse the removal procedure. For the door latch or outside door handle reinforcement, remove the outside door handle, reinforcement exterior retaining screw, and the latch mounting fasteners. Pull out the latch and rods from the door as a single assembly, disconnecting the rods and electrical connector if not done earlier. On a clean workbench, disconnect the outside handle and lock cylinder actuator rods from the latch or from the outside door handle reinforcement. Installation is the reverse of removal. To remove the door lock cylinder, first remove the door latch and outside door handle reinforcement, then slide the locking clip outwards and remove the lock cylinder. Remove the clip and rod arm from the lock cylinder. When installing the lock cylinder, push it all the way into the outside door handle reinforcement until it clicks into place, then install the locking clip. Installation is otherwise the reverse of removal. For the rear doors (all models), follow similar procedures as listed for the front doors, including removing the door trim panel and watershield, disconnecting the outside door handle, and addressing specific steps for lock cylinder, outer door handle, and inside door handle replacement. For coupe models with smaller "rear seat access" doors, the replacement steps are different and involve removing the handle and latches, both upper and lower, depending on the location, then reinstalling them in reverse order.

Once in every three months or after every 3000 miles, some light oil or lock lubricant should be applied to the hinges for door, hood trunk, and latch assemblies. Also, a thin coat of grease is recommended to be spread on the door latch strikers to avoid too much wearing out and aid for an easy movement. Sprayed graphite lubricant is also applicable in doors and trunks locks.

To remove the tailgate handle, start by removing the handle mounting bolts from the bedside. Then, carefully pry or pull off the handle trim cover. Next, rotate the plastic retaining clips off the control rods and detach the rods from the handle. After that, remove the latch mounting bolts and withdraw the latch from the end of the tailgate. If equipped, detach any linkage to the lock cylinder. To reinstall, simply reverse the removal steps and tighten all fasteners securely.

The power door lock system operates using door lock actuators mounted in each door and includes switches, actuators, lock and unlock relays, the Body Control Module (BCM), and associated wiring. Diagnosis usually involves simple checks of wiring connections and actuators for minor faults. The system utilizes bi-directional solenoids in the doors, mounted as part of the door latch. Lock switches have Lock and Unlock positions, sending signals to the BCM, which activates the door lock relays, providing voltage to each door lock solenoid. To troubleshoot, check circuit protection first, including fuses and circuit breakers. Verify voltage at the switches and check for continuity; if necessary, replace faulty switches. Check the wiring between the switches, BCM, door lock relay, and solenoid if needed. In case of an inoperative solenoid, test for voltage and ground, check for breaks in the wiring, and replace the solenoid if necessary. Communication for the power door lock system passes through the Body Control Module, and if the issue remains unresolved, retrieve trouble codes from the BCM using a scan tool. The keyless entry system uses a remote control transmitter sending an infrared signal to the receiver to operate the door lock system. Replace the battery when the transmitter's range decreases. To replace the key remote control battery, carefully separate the case halves, replace the battery, and snap the case back together. Programming replacement transmitters requires a specialized scan tool, so take the vehicle and transmitters to a dealer or qualified repair shop with the necessary tool to have the transmitter(s) programmed into the vehicle. Up to eight key fobs can be programmed to one car, and all fobs must be present during reprogramming.

A few drops of light oil or lock lubricant.

The door latch can be removed by disconnecting the electrical connector and detaching the rods.

The keyless entry system consists of a remote control transmitter that sends a coded infrared signal to a receiver, which operates the door lock system.

Once every 3000 miles or every three months.

To reduce wear and ensure free movement.

Replace the battery in the key remote control. To do this, carefully separate the case halves, replace the battery, and snap the case back together.

The components that can be removed and installed are the latch, lock cylinder, outside handle, inside release handle, and latch strikers.

For installation, simply reverse the removal process.

To remove the door lock cylinder, remove the door trim panel and plastic water shield.

To remove the latch from an access door, you need to remove the trim around the latch to access it for removal or adjustment. Access doors use two latches, one at the top and one at the bottom.

The outside handle can be removed by either removing the bolt cover and bolt, or by unclipping the lock trim cover and using a hooked tool to hold the bellcrank lever in the partially opened position while removing the handle.

They should be lubricated with a thin coat of grease.

When troubleshooting the power door lock system, it's advisable to check circuit protection first, followed by checking for voltage at the switches and testing switch continuity. If necessary, check the wiring between the switch and door lock solenoid. If a solenoid is not receiving voltage, investigate for an open or short in the wire between the solenoid and relay.

To remove the inside release handle from a door, release its cable and remove the mounting fasteners.

They should be lubricated with spray-on graphite lubricant.