My Garage
My Account
Cart
Genuine Chevrolet HHR Door Latch Assembly
Door Latch- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
9 Door Latch Assemblys found
Chevrolet HHR Lift Gate Latch Assembly
Part Number: 13584872$171.00 MSRP: $256.80You Save: $85.80 (34%)Ships in 1-2 Business Days
Chevrolet HHR Rear Side Door Lock Assembly
Part Number: 20791795$132.31 MSRP: $198.71You Save: $66.40 (34%)Ships in 1-2 Business Days
Chevrolet HHR Front Side Door Lock Assembly
Part Number: 20791793$130.46 MSRP: $194.17You Save: $63.71 (33%)
Chevrolet HHR Front Side Door Lock Assembly
Part Number: 20791792$170.23 MSRP: $255.65You Save: $85.42 (34%)Ships in 1-2 Business Days
Chevrolet HHR Rear Side Door Lock Assembly (W/ Actuator)
Part Number: 20791794$123.13 MSRP: $184.92You Save: $61.79 (34%)Ships in 1-2 Business Days
Chevrolet HHR Door Latch Assembly Parts Questions & Experts Answers
- Q: What is the recommended maintenance schedule for lubricating hinges, latch assemblies, and locks on doors, hood, and trunk for Chevrolet Cobalt,HHR and Saturn ION?A: Once in every three months or after every 3000 miles, some light oil or lock lubricant should be applied to the hinges for door, hood trunk, and latch assemblies. Also, a thin coat of grease is recommended to be spread on the door latch strikers to avoid too much wearing out and aid for an easy movement. Sprayed graphite lubricant is also applicable in doors and trunks locks.
- Q: How to remove and install Door Handle,Door Latch Assembly and Door Lock Cylinder for Chevrolet Cobalt,HHR and Saturn ION?A: To work on the front door, start by raising the window and then removing the door trim panel and watershield. For Cobalt/GS and ION models, disconnect the rod from the latch mechanism to the outside door handle and any electrical connectors from the door latch assembly, if applicable. Remove the latch mounting bolts and the inside handle retaining screw on ION models, and take out the handle, cable/rods, and latch as an assembly from the door. For lock cylinder and outer door handle replacement, follow specific steps for each model type. On Cobalt/GS models, remove the bolt securing the front of the handle from inside the door, then disconnect the lock cylinder rod and remove the lock cylinder mounting screws. On ION models, disconnect the lock cylinder rod and remove the lock cylinder from the door. For outer door handle replacement, lift up the handle and remove the plastic pushpin, then push the door handle towards the front of the vehicle to remove it from the pivot assembly in the door. For HHR models, remove the trim cap for the outside handle retaining screw, remove the screw, pull the door handle outwards, and remove the handle cover. To disengage the outside door handle lever from the handle reinforcement inside the door, pull it out of the door and to the rear. Inspect and replace the outside door handle seals if necessary. For the inside door handle, disconnect the actuator cable and reverse the removal procedure. For the door latch or outside door handle reinforcement, remove the outside door handle, reinforcement exterior retaining screw, and the latch mounting fasteners. Pull out the latch and rods from the door as a single assembly, disconnecting the rods and electrical connector if not done earlier. On a clean workbench, disconnect the outside handle and lock cylinder actuator rods from the latch or from the outside door handle reinforcement. Installation is the reverse of removal. To remove the door lock cylinder, first remove the door latch and outside door handle reinforcement, then slide the locking clip outwards and remove the lock cylinder. Remove the clip and rod arm from the lock cylinder. When installing the lock cylinder, push it all the way into the outside door handle reinforcement until it clicks into place, then install the locking clip. Installation is otherwise the reverse of removal. For the rear doors (all models), follow similar procedures as listed for the front doors, including removing the door trim panel and watershield, disconnecting the outside door handle, and addressing specific steps for lock cylinder, outer door handle, and inside door handle replacement. For coupe models with smaller "rear seat access" doors, the replacement steps are different and involve removing the handle and latches, both upper and lower, depending on the location, then reinstalling them in reverse order.
