GM 89059111 Joint Kit,Front Axle Propeller Shaft Universal

You can Select Your Vehicle to check if 89059111 fits your vehicle.

To remove a universal joint, it will vary depending on whether it is an outer snap-ring type or an injected plastic type. The snap rings are then removed with pliers, and force out the bearing caps. The U-joint is then removed and replaced with a new one and the bearing cap bores are inspected. For the injected plastic type, the snap-rings are removed if the joint has been rebuilt. Reassembly is the same as for the outer snap-ring joint, except the snap-rings are on the inner part of each bearing cap. If the joint is stiff after assembly, the yoke ears can be struck with a hammer to free up the joint.

A driveshaft is a tube or pair of tubes that transmits power between the transmission and differential, with universal joints located at either end and in the center of two-piece driveshafts. Single piece driveshafts have a splined yoke at the front that allows for movement during vehicle operation, while two-piece driveshafts have a slip joint on the front of the rear section and a center support bearing. The driveshaft assembly requires little service, with universal joints lubricated for life and replaced if problems arise. Inspection involves checking for dents, cracks, and oil leakage, as well as ensuring proper operation of universal joints and center bearings. Driveshaft mounting bolts should also be checked for tightness, and similar checks should be performed on the front driveshaft and driveaxles of 4WD models. Noise or vibration while driving may indicate problems with the driveshaft or other components.

A drive shaft is a tube or set of tubes that transfers power between either the transmission or the transfer case on 4WD models and the differential. Universal joints are positioned at each end of the driveshaft as well as in the center of two-piece driveshafts. On 2WD models, their driveshafts have a front splined yoke that slips into the transmission extension housing so that their length can increase and decrease. An oil seal prevents leakage at this point. Driveshafts on 4WD models tend to come with a splined yoke / companion flange at the transfer case end while two-piece driveshafts typically sport a slip joint at the front of the rear section. Center bearings carry the driveline when two-piece driveshafts are used. It's not often you need to service a drive shaft assembly but if anything goes wrong, replace worn universal joints since they have had to be greased for life. The drivshaft must be cleaned and checked for damage whenever lifting vehciles during servicing, ensuring that small weights used in balancing it do not detach. In most instances, noise or vibration when driving signifies trouble in the drivshaft whereas road testing can clarify whether this is right.

A driveshaft is a tube or pair of tubes that transmits power between the transmission or transfer case on 4WD models and the differential.

Start by placing it on a bench equipped with a vise. Use pliers to remove the snap-rings. Support the cross on a short piece of pipe or a large socket and press it out by closing the vise. Grip the bearing cup with locking pliers and remove it.

Before beginning the universal joint replacement procedure, it's crucial to have a universal joint service kit specific to your vehicle.

An oil seal prevents leakage at this point.

Before beginning the universal joint replacement procedure, it's crucial to have a universal joint service kit specific to your vehicle.

Reassemble the joint using the same steps as the outer snap-ring joint, but with the snap-rings on the inner part of each bearing cup. If difficulty is encountered during installation, strike the yoke with a hammer to allow the snap-ring groove to move into position.

The process for replacing the injected plastic type universal joint involves removing the snap-rings if the joint has been previously rebuilt, and pressing out the bearing caps.

During a driveshaft inspection, dents, cracks, and oil leakage should be checked. Additionally, the proper operation of universal joints and center bearings should be ensured.

In 2WD models, the driveshaft has a splined yoke at the front that allows it to slide back and forth within the transmission, with an oil seal to prevent fluid leakage and dirt entry.

The two types of universal joints mentioned are the outer snap-ring type and the injected plastic (inner snap-ring) type.

Noise or vibration while driving may indicate problems with the driveshaft or other components.

The two types of universal joints mentioned are the outer snap-ring type and the injected plastic (inner snap-ring) type.

The two types of universal joints mentioned are the outer snap-ring type and the injected plastic (inner snap-ring) type.

A driveshaft is a tube or pair of tubes that transmits power between the transmission and differential.

Driveshaft mounting bolts should be checked for tightness.

The process for replacing the outer snap-ring type universal joint involves removing the driveshaft and placing it on a bench equipped with a vise. The snap-rings are then removed with pliers, and a piece of pipe or socket is used to force out the bearing caps. The U-joint is then removed and replaced with a new one from a repair kit. The bearing cap bores are inspected for wear. Finally, the U-joint is reinstalled by pressing the bearing caps into place with a vise and installing snap-rings.