GM 20980075 Wheel Hub, Front

You can Select Your Vehicle to check if 20980075 fits your vehicle.

First, remove the front wheel lug nuts and raise the vehicle on jackstands to remove the hub assembly. Remove the tire and on a 4WD model, take off the hub cover and use a socket combined with large breaker bar to unscrew off driveaxle/hub nut. Brake disc as well as wheel speed sensor should be pulled out of the hub after that remove the hub retaining bolts from steering knuckle as well as disc shield. In case it is necessary tap out of side to side then pull out of steering knuckle. Before fitting a new hub assembly, clean mating surfaces at steering knuckle, bearing flange and knuckle bore. Afterward fit bearing assembly into steering knuckle (or onto drive-axle for 4WD models). Put brake disc, caliper mounting bracket, caliper and wheel speed sensor back in place (for 4WD models). Reinstall driveaxle/hub nut torquing it to specifications. Lastly put back wheel on jack stands finally tighten lug nuts to specifications while lowering vehicle.

Install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing.

To remove and install components in the front differential for AWD systems, follow these steps:Remove the stabilizer bar link and, if applicable, the front shock absorber.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.

After removing the axleshaft and rear wheels, the brake disc and retaining ring/key should be removed from the end of the axle housing.

1. Install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. 2. Install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. 3. Carefully drive in the axle shaft with a soft-face hammer. 4. Fill the differential with the proper lubricant. 5. Install the driveaxle and differential carrier splash shield. 6. Install the wheel and lug nuts. 7. Lower the vehicle. 8. Tighten the lug nuts to the proper torque specifications. 9. Check for proper operation.

The first step is to remove the axleshaft and oil seal.

The initial steps to remove and install components in the front differential of selectable 4WD systems are as follows: Loosen the wheel lug nuts. Raise the vehicle securely on jackstands. Remove the right front wheel. Remove the differential carrier splash shield if equipped. Drain the lubricant from the front differential. For 4WD systems, unbolt the right driveaxle from the axleshaft flange and support it out of the way. Remove the front axle shift motor and, if applicable, disconnect the front stabilizer link or remove the front shock absorber/coil spring assembly. On 2500/3500 models, remove the front axle bracket bolts and slide the bracket forward for additional clearance. Support the differential carrier with a floor jack and a block of wood.

After removing the hub assembly, the oil seal should be discarded.

The old bearing can be extracted from the housing using a bearing puller and slide hammer.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.

The new bearing can be installed using a bearing installer or a piece of pipe against the outer race.

Remove the hub retaining bolts from the steering knuckle and remove the disc shield.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.

After adjusting the bearings, the key and retaining ring should be installed.

Remove the hub retaining bolts from the steering knuckle and remove the disc shield.

1. Loosen the wheel lug nuts. 2. Raise the vehicle. 3. Place it securely on jackstands. 4. Remove the left front wheel. 5. Remove the differential carrier splash shield from under the front axle. 6. Remove the left driveaxle. 7. Drain the lubricant from the front differential. 8. Pull the left axle shaft out with a slide hammer and adapter. 9. Remove the deflector and seal from the differential. 10. Remove the bearing using a slide hammer and bearing remover attachment.

Remove the hub retaining bolts from the steering knuckle and remove the disc shield.

The first step is to remove the axleshaft and oil seal.

1. Loosen the wheel lug nuts. 2. Raise the vehicle. 3. Place it securely on jackstands. 4. Remove the left front wheel. 5. Remove the differential carrier splash shield from under the front axle. 6. Remove the left driveaxle. 7. Drain the lubricant from the front differential. 8. Pull the left axle shaft out with a slide hammer and adapter. 9. Remove the deflector and seal from the differential. 10. Remove the bearing using a slide hammer and bearing remover attachment.

To remove and install components in the front differential for 4WD systems, follow these steps: Remove the bolts securing the axle tube to the differential carrier and the nuts attaching the tube to its support bracket. Carefully remove the output shaft tube, ensuring no components fall out. Mount the tube in a vise and remove the internal components. Measure and remove the axleshaft bearing using a slide hammer and bearing remover attachment. For installation, install the bearing to the original depth using a bearing driver or socket, then install a new seal and deflector, lubricating the seal lips with grease. Carefully drive in the axleshaft, followed by the internal components. Apply RTV sealant to the tube-to-differential housing mating surface, and install the tube assembly, tightening bolts and nuts to specified torques. Reinstall the driveaxle, front axle shift motor, and fill the differential with lubricant.

The initial steps are to remove the axleshaft and rear wheels.

To remove and install components in the front differential for 4WD systems, follow these steps: Remove the bolts securing the axle tube to the differential carrier and the nuts attaching the tube to its support bracket. Carefully remove the output shaft tube, ensuring no components fall out. Mount the tube in a vise and remove the internal components. Measure and remove the axleshaft bearing using a slide hammer and bearing remover attachment. For installation, install the bearing to the original depth using a bearing driver or socket, then install a new seal and deflector, lubricating the seal lips with grease. Carefully drive in the axleshaft, followed by the internal components. Apply RTV sealant to the tube-to-differential housing mating surface, and install the tube assembly, tightening bolts and nuts to specified torques. Reinstall the driveaxle, front axle shift motor, and fill the differential with lubricant.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.