Make sure this part fits

Chevrolet 20877208 Shaft Assembly, Propeller

2009 Chevrolet Tahoe

Customer Questions & Expert Answers (5)
GM 20877208 Shaft Assembly, Propeller
  • Part Description
    SHAFT, Propeller
  • Replaces
    25810572
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chevrolet
    Manufacturer Part Number20877208
    Part DescriptionSHAFT, Propeller
    Item Dimensions65.4 x 4.2 x 4.1 inches
    Item Weight13.90 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces25810572
    ManufacturerGeneral Motors
    SKU20877208
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2009 Chevrolet Tahoe8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex4 DOOR 1/2 TON
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 20877208 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install the driveshaft on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL? Posted by Customer
    A:
    Raising the vehicle and supporting it on jackstands, with the front wheels blocked, would remove the rear driveshaft. In order to reinstall in the same position reference marks should be made on the driveshaft and pinion flange and ensure that the transmission is in Neutral with the parking brake off. The drive shaft should be lowered by removing its back u-joint bolts and retainers then slid out of transfer case or transmission. When installing, slide front end into transmission or transfer case then raise rear into position with marks aligned. Afterward, all bolts must be tightened to their proper torque specifications and clamps used to secure bearing caps. For 4WD models' front drive shaft, raise vehicle using jack stands after removal of differential carrier splash shield if any. The boot at the transfer case output shaft should be disengaged and relationship between driveshaft and companion flange marked for future reference. Thereafter disconnect bolts as well as clamps from differential flange while pushing driveshaft toward rear so that it can be separated from this flange before lowering it down to pull out of transfer case. To install, insert a sliding shaft that has splines at its rear through transfer case's output ends while aligning marks attached to them with those found on companion flange's front end. Install clamps together with bolts tightly according to specified torque values whereas push up boot over groove of transfer case output shaft where new clip will have been crimped into place subsequently using clamp-crimping pliers for reinforcement purposes. Lastly, splash shield of front differential carrier should be installed back there again.
    Posted by GMPartsGiant Specialist
    Q:
    What is a driveshaft for the 2010 Chevrolet Tahoe? Posted by Customer
    A:
    A driveshaft is a tube or pair of tubes that transmits power between the transmission and differential.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How should the rear driveshaft be removed for the 2011 GMC Yukon? Posted by Customer
    A:
    The rear universal joint bolts and retainers should be removed, and the driveshaft lowered and slid out of the transmission or transfer case.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What may indicate problems with the driveshaft or other components for the 2011 GMC Yukon? Posted by Customer
    A:
    Noise or vibration while driving may indicate problems with the driveshaft or other components.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Drive Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 20877208, the Right Choice

To ensure reliability, purchase GM part # 20877208 Shaft Assembly, Propeller. It is sometimes referred to as Chevrolet Drive Shaft. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Chevrolet Tahoe models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 20877208 Shaft Assembly, Propeller. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Chevrolet parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly