Make sure this part fits

Buick 1988718 Starter Motor, Remanufactured

1982-1986 Buick

Customer Questions & Expert Answers (14)
GM 1988718 Starter Motor, Remanufactured
  • Part Description
    STARTER, Starter Motor
  • Manufacturer
    General Motors
Make sure this part fits
$79.89 MSRP: $150.74
You Save: $70.85 (47%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Buick
    Manufacturer Part Number1988718
    Part DescriptionSTARTER, Starter Motor
    Item Dimensions6.2 x 6.1 x 12.4 inches
    Item Weight14.60 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU1988718
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1983-1986 Buick Skyhawk4 Cyl 2.0L2 DOOR, 4 DOOR, CUSTOM 2 DOOR, CUSTOM 2 DOOR NOTCHBACK, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR, LIMITED WAGON, SPORT 2 DOOR, STATION WAGON, T-TYPE 2 DOOR
    1982-1985 Buick Skylark6 Cyl 2.8L2 DOOR, 4 DOOR, CUSTOM 2 DOOR, CUSTOM 4 DOOR, LIMITED 2 DOOR, LIMITED 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 1988718 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How do you remove and install the starter for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To remove and install the starter, start by disconnecting the ground cable from the battery. Then, raise the vehicle and support it with jack stands. Next, disconnect the leads at the starter solenoid, marking each with coded tape for easy identification later. Temporarily refit the securing nuts to the terminals. Remove the bolts securing the plastic starter shield and slide it back to expose the starter mounting bolts. Take out the starter to engine brace and then remove the two starter motor mounting bolts. Finally, remove the starter. To reinstall, follow the reverse order of removal, tightening the mount bolts first to the specified torque and then tightening the front bracket bolt and nut. Make sure to replace any shims that were removed for proper alignment. Refit the wires to the solenoid terminals using the identification coding.
    Posted by GMPartsGiant Specialist
    Q:
    What are the possible causes and solutions for a starter motor that does not rotate on Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    Ensure that the speed selector lever is in 'N' or 'P' for automatic transaxle or that the clutch pedal is depressed for manual transaxle if the starter motor does not rotate when operated. Verify that the battery is charged and all cables, at both the battery and starter solenoid terminals, are secure. If the motor can be heard spinning but the engine isn't cranked, the overrunning clutch in the starter motor is likely slipping, requiring removal and dismantling. If the starter motor doesn't operate, but a loud 'click' is heard from the solenoid plunger, the fault lies in the main solenoid contacts or the starter motor itself. In cases where the solenoid plunger doesn't move, the solenoid may be defective or the solenoid circuit open. You can check the solenoid by connecting a jumper lead between the battery (+) and the 'S' terminal on the solenoid. If the starter motor operates, the fault lies in the ignition or neutral start switches or their interconnecting wiring. If it doesn't, the starter/solenoid assembly should be removed for testing and repair. If the engine cranks at an unusually slow speed, check the battery charge and terminal connections, oil grade, and ensure no mechanical fault within the power unit. Run the engine to normal operating temperature, disconnect the battery feed wire to the distributor cap to prevent engine firing during cranking, then connect a voltmeter positive lead to the starter motor terminal of the solenoid and the negative lead to ground. Ignite the switch, take the voltmeter readings once steady, but don't let the starter motor turn for more than 30 seconds at a time. A reading of 9 volts or more with normal cranking speed indicates a good condition, while the same voltage but slow cranking speed denotes a faulty motor. A reading of less than 9 volts with slow cranking speed suggests the solenoid contacts are likely at fault and should be replaced.
    Posted by GMPartsGiant Specialist
    Q:
    How to dismantle the brush assembly and Starter for Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To install the brush assembly to the field frame, first, install the brushes to their holders and then assemble the insulated and grounded brush holders together with the V-spring and locate the unit on its support pin. Push the holders and spring to the bottom of the support and rotate the spring to engage the V in the support slot. Connect the ground wire to the ground brush and the field lead wire to the insulated brush and repeat the operations for the second set. Smear silicone oil onto the drive end of the armature shaft and slide the clutch assembly (pinion to the front) onto the shaft, followed by sliding the pinion stop/retainer onto the shaft with its open end facing away from the pinion. Stand the armature vertically on a piece of wood, position the snap-ring on the end of the shaft, and using a hammer and a piece of hardwood, drive the snap-ring onto the shaft. Slide the snap-ring until it drops into its groove. Install the thrust collar on the shaft so that the shoulder is next to the snap-ring and use pliers to squeeze the thrust collar and stop/retainer together until the snap-ring fully enters the retainer.
    Posted by GMPartsGiant Specialist
    Q:
    What should be removed to expose the starter mounting bolts for the 1981 Buick Skylark? Posted by Customer
    A:
    Remove the bolts securing the plastic starter shield and slide it back.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    How should the ground wire and field lead wire be connected to the brush assembly for the 1981 Buick Skylark? Posted by Customer
    A:
    Connect the ground wire to the grounded brush and the field lead wire to the insulated brush.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What should be done with roller-type clutches during the disassembly process for the 1985 Buick Skylark? Posted by Customer
    A:
    Roller-type clutches should not be disassembled and are serviced as complete units.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What should you check if the engine cranks at an unusually slow speed for the 1983 Buick Skylark? Posted by Customer
    A:
    Check the battery charge and terminal connections, oil grade, and ensure no mechanical fault within the power unit.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What does a reading below the 1995 Chevrolet Beretta with slow cranking indicate? Posted by Customer
    A:
    It may indicate burned solenoid contacts, a bad starter motor, discharged battery, or a bad connection.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What should be done before starting the removal process of the 1987 Chevrolet Beretta? Posted by Customer
    A:
    Detach the cable from the negative terminal of the battery and ensure the lockout feature is turned off if applicable.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    How should the snap-ring be exposed and extracted during disassembly for the 1980 Oldsmobile Omega? Posted by Customer
    A:
    Slide the two-section thrust collar off the armature shaft to expose the snap-ring. Extract the snap-ring from its shaft groove and slide the stop/retainer and overrunning clutch assembly from the armature shaft.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What should be done with roller-type clutches during the disassembly process of the 1983 Pontiac Phoenix? Posted by Customer
    A:
    Roller-type clutches should not be disassembled and are serviced as complete units.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What could be the issue if the solenoid plunger doesn't move of the 1983 Pontiac Phoenix? Posted by Customer
    A:
    The solenoid may be defective or the solenoid circuit open.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    Q:
    What should be done after installing the brush assembly for the first set of brushes of the 1982 Pontiac Phoenix? Posted by Customer
    A:
    After installing the first set of brushes, repeat the same operations for the second set of brushes.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Starter
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 1988718, the Right Choice

To ensure reliability, purchase GM part # 1988718 Starter Motor, Remanufactured. It is sometimes referred to as Buick Starter. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Buick Skyhawk, Skylark models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 1988718 Starter Motor, Remanufactured. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Buick parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly