How to inspect and replace flexible brake hoses?

About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the above defects are found, the hose should be replaced with a new one. To disconnect a brake hose from the brake line, the metal tube nut should be unscrewed with a flare nut wrench, and the U-clip should be removed from the female fitting at the bracket. The hose can then be removed from the bracket and disconnected from the caliper, discarding the sealing washers. When attaching the new brake hose, new sealing washers should be used, and it should be securely attached to the caliper or wheel cylinder. To reattach a brake hose to the metal line, the end of the hose should be inserted through the frame bracket, ensuring it is not twisted, and the metal line should be attached by tightening the tube nut fitting securely. The U-clip should be installed at the frame bracket. It is important to check that the suspension or steering components do not make contact with the hose, and an assistant can help by pushing down on the vehicle and turning the steering wheel lock-to-lock during inspection. Finally, the brake system should be bled and the metal brake lines should be replaced using the correct parts, avoiding the use of copper tubing. Prefabricated brake lines with flared tube ends and fittings can be used, and they should be well supported in the brackets with sufficient clearance from moving or hot components. After installation, the master cylinder fluid level should be checked and fluid added as necessary. The brake system should be bled and the brakes carefully tested before the vehicle is placed into normal operation.

Genuine Saturn LS1 Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Lines found

View related parts
Saturn LS1 Pipe Asm,Front Brake Rear
Part Number: 90539582
$33.57 MSRP: $40.62
You Save: $7.05 (18%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Brake Pressure Mod Valve Front Brake
Part Number: 90539587
$13.31 MSRP: $14.52
You Save: $1.21 (9%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe,Brake
Part Number: 21019042
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Front Brake Combination Valve
Part Number: 90539578
Product Specifications
- Other Name: PIPE, Hydraulic Brake Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Front Brake Combination Valve
Part Number: 90539579
Product Specifications
- Other Name: PIPE, Hydraulic Brake Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Brake Pressure Mod Valve Rear Brake
Part Number: 90539588
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe
Part Number: 21019246
Product Specifications
- Other Name: PIPE, Hydraulic Brake; Brake Line
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe
Part Number: 21019247
Product Specifications
- Other Name: PIPE, Hydraulic Brake; Brake Line
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Front Brake Rear
Part Number: 90539591
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Front Brake Rear
Part Number: 90539592
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Rear Brake
Part Number: 90539594
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Rear Brake,RH
Part Number: 21019262
Product Specifications
- Other Name: PIPE, Hydraulic Brake; Brake Line
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Pipe Asm,Rear Brake,LH
Part Number: 21019263
Product Specifications
- Other Name: PIPE, Hydraulic Brake; Brake Line
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L
View related parts
Saturn LS1 Hose,Rear Brake
Part Number: 90445758
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose
- Position: Rear
- Replaces: 21019248
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Saturn LS1 | LS, LS1, LS2, LW1, LW2 | 4 Cyl 2.2L

Saturn LS1 Brake Line

The Brake Line in Saturn LS1 vehicles is used to ensure that brake fluid from the master cylinder gets to the brake caliper pistons hence enhancing the hydraulic brake system. Due to the situations of corrosion and review shocks, metal brake lines can be subjected to fluid leaks and loss of hydraulic pressure. The brake hoses can also get worn in physical and internal parts of the brake system which impacts the brake efficiency. For replacement only, there are prebent brake line kits and stainless steel brake hoses that can be easily installled. The replacement of the flexible rubber hoses with stainless steel braided ones typically yields a stiffer and more sensitive brake pedal, which is beneficial for aggressive driving.

Each OEM Saturn LS1 Brake Line we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Saturn LS1 Brake Line Parts Questions & Experts Answers

Pipe
21019246
Q: How to inspect and replace flexible brake hoses?
A: About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the above defects are found, the hose should be replaced with a new one. To disconnect a brake hose from the brake line, the metal tube nut should be unscrewed with a flare nut wrench, and the U-clip should be removed from the female fitting at the bracket. The hose can then be removed from the bracket and disconnected from the caliper, discarding the sealing washers. When attaching the new brake hose, new sealing washers should be used, and it should be securely attached to the caliper or Wheel Cylinder. To reattach a brake hose to the metal line, the end of the hose should be inserted through the frame bracket, ensuring it is not twisted, and the metal line should be attached by tightening the tube nut fitting securely. The U-clip should be installed at the frame bracket. It is important to check that the suspension or steering components do not make contact with the hose, and an assistant can help by pushing down on the vehicle and turning the steering wheel lock-to-lock during inspection. Finally, the brake system should be bled and the metal brake lines should be replaced using the correct parts, avoiding the use of copper tubing. Prefabricated brake lines with flared tube ends and fittings can be used, and they should be well supported in the brackets with sufficient clearance from moving or hot components. After installation, the master cylinder fluid level should be checked and fluid added as necessary. The brake system should be bled and the brakes carefully tested before the vehicle is placed into normal operation.

Related Saturn LS1 Parts

Browse by Year

2000 Brake Line