How do you remove the ignition switch?

Proceed with removing the ignition switch by disconnecting the two wiring leads, starting with the one farthest from the steering wheel. Remove the stud and screw securing the switch to the column, and lift off the switch, making sure to pull it up from the column due to the protruding ignition actuator rod. Before installing the new switch, use a flat-head screwdriver to move the slider inside the switch to the 'Accessory' position on the extreme right, then slide it two detents to the left to the 'off/unlock' position. This position is necessary for installation. Place the switch on the column, guiding the actuator rod into the slider recess. Install the stud and screw, tightening them to specifications. Finally, connect the two wiring leads to the switch and reverse the procedure.

Genuine Oldsmobile Omega Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Ignition Switches found

View related parts
Oldsmobile Omega Switch,Ignition & Start
Part Number: 1990116
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Oldsmobile Omega Switch,Steering Column Ignition
Part Number: 1990115
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Oldsmobile Omega Switch,Steering Column Ignition Lock
Part Number: 7843451
Product Specifications
- Other Name: SWITCH, Ignition Switch; Ignition Lock Cylinder, Ignition Switch
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Oldsmobile Omega Switch,Ignition Key Alarm
Part Number: 26022717
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Oldsmobile Omega Switch Assembly, Ignition Key Warning Alarm
Part Number: 7804414
Product Specifications
- Other Name: SWITCH, Ignition Switch Warning, Lock, Headlamp,Theft Deterrent or Frt/Rear/Side Object
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Oldsmobile Omega | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR | 4 Cyl 2.5L, 6 Cyl 2.8L

Oldsmobile Omega Ignition Switch

The Oldsmobile Omega Ignition Switch is an armor from the ignition and charging systems which is used to start the car motors and turn on the other electrical parts. These commonly used to be opened with a mechanical key; however, newer designs may use technologies such as push button to open the door. It supplies current to the starter solenoid and ignition parts and sometimes the parts such as the radio, and power windows. However, there is always a possibility of hotwiring, and the major ignition switches are relatively more susceptible to damages and are of the plug in type where each replacement is directly related to the particular Omega brand of car.

Each OEM Oldsmobile Omega Ignition Switch we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Oldsmobile Omega Ignition Switch Parts Questions & Experts Answers

Switch,Steering Column Ignition
1990115
Q: How do you remove the ignition switch?
A: Proceed with removing the ignition switch by disconnecting the two wiring leads, starting with the one farthest from the steering wheel. Remove the stud and screw securing the switch to the column, and lift off the switch, making sure to pull it up from the column due to the protruding ignition actuator rod. Before installing the new switch, use a flat-head screwdriver to move the slider inside the switch to the 'Accessory' position on the extreme right, then slide it two detents to the left to the 'off/unlock' position. This position is necessary for installation. Place the switch on the column, guiding the actuator rod into the slider recess. Install the stud and screw, tightening them to specifications. Finally, connect the two wiring leads to the switch and reverse the procedure.