How do you replace the shift cable on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the shift cable, start by disconnecting the negative cable from the battery. Locate the vacuum actuator, which can be found on top or underneath the right fender well. If it is located below the battery, remove the battery first. Squeeze the two locking fingers of the cable ferrule and pull the cable out of the bracket. Remove the cable housing bolts and pull out the housing slightly. Unscrew the coupling nut to detach the cable from the shift cable housing. Remove the shift cable assembly. To install the new cable, guide the end through the hole in the shift cable housing and push it into the shift fork shaft. Install the shift cable housing on the differential carrier and tighten the bolts. Spread the retainer clip, engage the cable end with the actuator, and release the retainer clip. Connect the shift cable to the actuator and attach the vacuum hose to the actuator. To remove the vacuum actuator, detach the vacuum hose and disconnect the shift cable. Remove the actuator retaining bolts and remove the actuator. Installation is the reverse of removal.

How do I remove the shift cable on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the shift cable, start by detaching the cable from the negative terminal of the battery and applying the parking brake. Then, block the rear wheels and shift the transmission into Neutral. If applicable, remove the transfer case shield and pry the cable end from the transmission control lever stud. Remove the cable from the transmission oil pan clip and the horseshoe retainer from the shift cable housing. Squeeze the cable retainer and pull the cable toward the back of the vehicle to disconnect it. For vehicles with a column shift, remove the steering column trim filler panel, and for floor shift vehicles, pry the shift cable from the shift lever. Remove the horseshoe clip retaining the cable to the bracket on the steering column and squeeze the cable retainer to remove the cable from the bracket. If necessary, remove the floor console, cowl trim panel, door sill trim plate, seat, and front carpet, and pry the cable grommet from the floor before removing the cable and grommet from the vehicle. To install the cable, follow the reverse order of removal, being careful not to damage the rubber boot. For adjustment, apply the parking brake and remove the retaining clip from the rear support bracket. Separate the body-core adjuster from the range selector pin and place the transmission shift selector shaft and lever in Neutral. Remove the horseshoe retainer from the shift cable and the cable from the transmission oil pan clip. Reinstall the cable onto the transmission oil pan clip and the horseshoe retainer onto the shift cable. Ensure the transmission shift lever and selector shaft are still in Neutral and snap the body-core adjustment onto the transmission selector shaft. Push the locking tab into the body core until it snaps, and insert the horseshoe retainer into the shift cable. Finally, check the adjustment to ensure the shift lever goes into all positions and the engine starts only in the P or N positions. Readjust the shift cable and park/neutral switch if necessary to meet these criteria.

Genuine GMC Jimmy Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Shift Cables found

View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189202
$54.06 MSRP: $104.96
You Save: $50.90 (49%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15021556, 15036347
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189200
$99.26 MSRP: $151.63
You Save: $52.37 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15006393
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189203
$81.77 MSRP: $122.26
You Save: $40.49 (34%)
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15033322, 15746210
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Throttle Valve Cable Assembly
Part Number: 25515599
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Throttle Valve ; Cable, Transmission Throttle Valve Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1991 GMC Jimmy | 1/2 TON | 8 Cyl 6.2L Diesel
View related parts
GMC Jimmy Transmission Throttle Valve Cable Assembly
Part Number: 25515598
Product Specifications
- Other Name: Cable Assembly, Trans Throttle Valve Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 GMC Jimmy | 1/2 TON | 8 Cyl 5.0L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189201
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15021558
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Select Lever Cable
Part Number: 15713353
Product Specifications
- Other Name: Cable,Automatic Transmission Range Selector Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15721262
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189199
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15006391, 15036346
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15721261
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Selector Lever Cable Assembly
Part Number: 15189198
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Range Selector Lever ; Cable, Transmission Shift Control Cable
- Replaces: 15746211, 15033323
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2001 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Shifter Cable Assembly
Part Number: 12544814
Product Specifications
- Other Name: Cable Asm,Automatic Transmission Range Selector Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | 2 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Transmission Throttle Valve Control CABLE
Part Number: 15661601
Product Specifications
- Other Name: Cable, Transmission Throttle Valve Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | 2 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Cable,Automatic Transmission Parking Lock
Part Number: 26082803
Product Specifications
- Other Name: CABLE, Automatic Transmission Parking Lock; Cable, Parking Brake Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Transmission Throttle Valve Cable Assembly
Part Number: 25507541
Product Specifications
- Other Name: Cable Assembly, Trans Detent Control ; Cable, Transmission Throttle Valve Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 GMC Jimmy | 1/2 TON | 8 Cyl 5.0L
View related parts
GMC Jimmy Automatic Transmission Throttle Valve Cable Assembly
Part Number: 10142019
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Throttle Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Throttle Valve Cable
Part Number: 10174462
Product Specifications
- Other Name: Cable,Automatic Transmission Throttle Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Throttle Valve Cable Assembly
Part Number: 14102146
Product Specifications
- Other Name: Cable Assembly, Automatic Transmission Throttle Valve ; Cable, Transmission Throttle Valve Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1991 GMC Jimmy | 1/2 TON | 6 Cyl 4.3L
View related parts
GMC Jimmy Transmission Throttle Valve Cable Assembly
Part Number: 15997264
Product Specifications
- Other Name: Cable Assembly, Transfer Case Control ; Cable, Transfer Case External Shift Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L
View related parts
GMC Jimmy Automatic Transmission Range Select Lever Cable
Part Number: 15730543
Product Specifications
- Other Name: Cable,Automatic Transmission Range Selector Lever
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 GMC Jimmy | 2 DOOR, 4 DOOR | 6 Cyl 4.3L

GMC Jimmy Shift Cable

Each OEM GMC Jimmy Shift Cable we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Jimmy Shift Cable Parts Questions & Experts Answers

Automatic Transmission Range Selector Lever Cable Assembly
15189203
Q: How do you replace the shift cable on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the shift cable, start by disconnecting the negative cable from the battery. Locate the vacuum actuator, which can be found on top or underneath the right fender well. If it is located below the battery, remove the battery first. Squeeze the two locking fingers of the cable ferrule and pull the cable out of the bracket. Remove the cable housing bolts and pull out the housing slightly. Unscrew the coupling nut to detach the cable from the shift cable housing. Remove the shift cable assembly. To install the new cable, guide the end through the hole in the shift cable housing and push it into the shift fork shaft. Install the shift cable housing on the differential carrier and tighten the bolts. Spread the retainer clip, engage the cable end with the actuator, and release the retainer clip. Connect the shift cable to the actuator and attach the vacuum hose to the actuator. To remove the vacuum actuator, detach the vacuum hose and disconnect the shift cable. Remove the actuator retaining bolts and remove the actuator. Installation is the reverse of removal.
Automatic Transmission Range Selector Lever Cable Assembly
15189199
Q: How do I remove the shift cable on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the shift cable, start by detaching the cable from the negative terminal of the battery and applying the parking brake. Then, block the rear wheels and shift the transmission into Neutral. If applicable, remove the transfer case shield and pry the cable end from the transmission control lever stud. Remove the cable from the transmission oil pan clip and the horseshoe retainer from the shift cable housing. Squeeze the cable retainer and pull the cable toward the back of the vehicle to disconnect it. For vehicles with a column shift, remove the steering column trim filler panel, and for floor shift vehicles, pry the shift cable from the shift lever. Remove the horseshoe clip retaining the cable to the bracket on the steering column and squeeze the cable retainer to remove the cable from the bracket. If necessary, remove the floor console, cowl trim panel, door sill trim plate, seat, and front carpet, and pry the cable grommet from the floor before removing the cable and grommet from the vehicle. To install the cable, follow the reverse order of removal, being careful not to damage the rubber boot. For adjustment, apply the parking brake and remove the retaining clip from the rear support bracket. Separate the body-core adjuster from the range selector pin and place the transmission shift selector shaft and lever in Neutral. Remove the horseshoe retainer from the shift cable and the cable from the transmission oil pan clip. Reinstall the cable onto the transmission oil pan clip and the horseshoe retainer onto the shift cable. Ensure the transmission shift lever and selector shaft are still in Neutral and snap the body-core adjustment onto the transmission selector shaft. Push the locking tab into the body core until it snaps, and insert the horseshoe retainer into the shift cable. Finally, check the adjustment to ensure the shift lever goes into all positions and the engine starts only in the P or N positions. Readjust the shift cable and park/neutral switch if necessary to meet these criteria.