How do you remove the rear stabilizer bar and link?

To remove and install a sway bar kit on a vehicle, begin by loosening the rear wheel lug nuts and raising the rear of the vehicle on jackstands. Block the front wheels and remove the back wheels. Next, remove the spare tire and the left and right side sway bar link-to-sway bar kit nuts, along with the washers and bushings.

How do you remove the front stabilizer bar and link?

To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle on jackstands. Remove the front wheels and unbolt the intermediate driveaxle shaft bracket from the subframe. If it's an all-wheel drive model, remove the rear driveshaft. Detach the sway bar link from the strut or bar by holding the ballstud with a wrench and unscrewing the nut. Then, detach the tie-rod ends from the steering knuckle. Support the rear of the subframe with floor jacks and remove the subframe rear reinforcement bolts. Loosen the subframe front reinforcement bolts and the subframe front mounting bolts. Loosen the subframe rear mounting bolts and slowly lower the floor jacks while backing out the rear bolts. Remove the bolts and detach the sway bar kit bushing retainer. Inspect and replace the bushings if necessary. Clean the bushing area of the sway bar kit with a wire brush and lubricate the new bushings with vegetable oil. For installation, reverse the removal steps and tighten the fasteners to the specified torque values. Raise the subframe using floor jacks and tighten the mounting bolts in the proper order. Finally, install the wheels and tighten the lug nuts to the specified torque.

Genuine GMC Acadia Sway Bar Kit

Stabilizer Sway Bar Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Sway Bar Kits found

View related parts
GMC Acadia Shaft, Front Stabilizer
Part Number: 15837426
$219.13 MSRP: $346.34
You Save: $127.21 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT, Stabilizer; Stabilizer Bar
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2017 GMC Acadia | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
GMC Acadia Shaft Assembly, Front Stab
Part Number: 85127573
$70.99 MSRP: $111.68
You Save: $40.69 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Front
- Replaces: 84346082, 84293442, 23108029
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2023 GMC Acadia | DENALI SUV, SLE SUV, SLE2 & ALL TERRAIN SUV, SLE2 SUV, SLT & ALL TERRAIN SUV, SLT SUV, SLT2 SUV | 4 Cyl 2.0L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
GMC Acadia Shaft, Front Stabilizer
Part Number: 15905568
$203.33 MSRP: $321.36
You Save: $118.03 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT, Stabilizer; Stabilizer Bar
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2017 GMC Acadia | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
GMC Acadia Shaft Assembly, Rear Stab
Part Number: 84617934
$78.40 MSRP: $123.32
You Save: $44.92 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Bar
- Position: Rear
- Replaces: 84111035, 84293436
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2023 GMC Acadia | DENALI SUV, SLE SUV, SLE2 & ALL TERRAIN SUV, SLE2 SUV, SLT & ALL TERRAIN SUV, SLT SUV, SLT2 SUV | 4 Cyl 2.0L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
GMC Acadia Shaft, Rear Stabilizer
Part Number: 15896941
$679.11 MSRP: $1229.16
You Save: $550.05 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT, Stabilizer; Stabilizer Bar
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2017 GMC Acadia | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L

GMC Acadia Sway Bar Kit

The GMC Acadia Sway Bar Kit in particular, is specifically tuned for vehicle handling: Sway bars serve to link the opposing ends of the suspension system, therefore decreasing the amount of body roll during cornering or when over rough terrains. This anti roll bar works by exerting a force whereby roll stiffness is increased without varying the vertical spring rate and hence resulting in an improvement of the grip forces. Different types of Sway bar kits over the years have been applied on GMC Acadia that include adjustable Sway bar and active anti-roll bars. Such systems can allow the stiffness to be varied to improve the car's behaviour and comfort. Conventional installing of sway bars passing the shocks between wheels where a "waddling" feeling takes place when lorries traverse terribly devastated areas but latest models work towards reducing such impacts.

Each OEM GMC Acadia Sway Bar Kit we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Acadia Sway Bar Kit Parts Questions & Experts Answers

Shaft Assembly, Rear Stab
84617934
Q: How do you remove the rear stabilizer bar and link?
A: To remove and install a sway bar kit on a vehicle, begin by loosening the rear wheel lug nuts and raising the rear of the vehicle on jackstands. Block the front wheels and remove the back wheels. Next, remove the spare tire and the left and right side sway bar link-to-sway bar kit nuts, along with the washers and bushings.
Shaft, Front Stabilizer
15837426
Q: How do you remove the front stabilizer bar and link?
A: To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle on jackstands. Remove the front wheels and unbolt the intermediate driveaxle shaft bracket from the subframe. If it's an all-wheel drive model, remove the rear driveshaft. Detach the sway bar link from the strut or bar by holding the ballstud with a wrench and unscrewing the nut. Then, detach the tie-rod ends from the Steering Knuckle. Support the rear of the subframe with floor jacks and remove the subframe rear reinforcement bolts. Loosen the subframe front reinforcement bolts and the subframe front mounting bolts. Loosen the subframe rear mounting bolts and slowly lower the floor jacks while backing out the rear bolts. Remove the bolts and detach the sway bar kit bushing retainer. Inspect and replace the bushings if necessary. Clean the bushing area of the sway bar kit with a wire brush and lubricate the new bushings with vegetable oil. For installation, reverse the removal steps and tighten the fasteners to the specified torque values. Raise the subframe using floor jacks and tighten the mounting bolts in the proper order. Finally, install the wheels and tighten the lug nuts to the specified torque.