How do you remove and install the CKP sensor in a Buick Enclave,Chevrolet Traverse and GMC Acadia?

Raise the front of the vehicle and support it securely on jackstands. Remove the heal shield covering the wiring harness and sensor. Disconnect the electrical connector from the CKP sensor, which is located at the rear of the engine block on the firewall side. Unscrew the mounting fastener and remove the CKP sensor. Before installing the sensor, lubricate the O-ring with clean engine oil. Installation is otherwise the reverse of removal.

Genuine Chevrolet Traverse Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Crankshaft Position Sensors found

View related parts
Chevrolet Traverse Sensor Assembly, Crankshaft Position
Part Number: 12615626
$16.48 MSRP: $31.12
You Save: $14.64 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Traverse | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
Chevrolet Traverse Sensor Assembly, Crankshaft Position
Part Number: 12674702
$46.08 MSRP: $86.94
You Save: $40.86 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly, Cr/Shf Posn
- Replaces: 12632872, 12627185
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2019 Chevrolet Traverse | LT EXTENDED 4 DOOR SUV | 4 Cyl 2.0L
View related parts
Chevrolet Traverse Sensor,Crankshaft Position
Part Number: 12613030
$34.68 MSRP: $65.45
You Save: $30.77 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Replaces: 12590991
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 Chevrolet Traverse | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
Chevrolet Traverse Sensor Assembly, Crankshaft Position
Part Number: 12664495
$16.17 MSRP: $30.50
You Save: $14.33 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly, Cr/Shf Posn; Crankshaft Position Sensor, Crankshaft Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Traverse | LS EXTENDED 4 DOOR SUV, LT EXTENDED 4 DOOR SUV, LTZ EXTENDED 4 DOOR SUV | 6 Cyl 3.6L

Chevrolet Traverse Crankshaft Position Sensor

Crankshaft Position Sensor is an essential electrical part in the Chevrolet Traverse automative sector that signifies the crankshaft position and its revolutions. It relays this information to the powertrain control module that then uses the data to adjust the fuelinjectoins and the ignition timing to optimize on the performance of the engine. The different forms of crankshaft position sensors that have been used are the inductive, Hall Effect, magnetoresistive and the optical sensors. The induced sensors are non-active, or said to be permanently non-active as well as the Hall and magnetoresistive sensors. Optical sensors give very sharp edges because they are based on the physical measurement of the signal and can foul easily. Commonly it is fixed on the crank pulley, a flywheel or directly on the crankshaft and a damaged sensor causes starting or stalling problems. All in all, the Crankshaft Position Sensor is an important component of the modern engine management systems, which contributes to car's performance and durability.

Each OEM Chevrolet Traverse Crankshaft Position Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Traverse Crankshaft Position Sensor Parts Questions & Experts Answers

Sensor Assembly, Crankshaft Position
12615626
Q: How do you remove and install the CKP sensor in a Buick Enclave,Chevrolet Traverse and GMC Acadia?
A: Raise the front of the vehicle and support it securely on jackstands. Remove the heal shield covering the wiring harness and sensor. Disconnect the electrical connector from the CKP sensor, which is located at the rear of the engine block on the firewall side. Unscrew the mounting fastener and remove the CKP sensor. Before installing the sensor, lubricate the O-ring with clean engine oil. Installation is otherwise the reverse of removal.