What does the Crankshaft Position (CKP) sensor provide to the PCM?

The Crankshaft Position (CKP) sensor provides the PCM with a crankshaft position signal, which the PCM uses to determine the spark sequence for each cylinder, control ignition timing, and calculate engine speed. The signal is also used by the Onboard Diagnostic system for misfire detection. The sensor is triggered by slots cut into a reluctor ring on the crankshaft and is positioned approximately 0.050 inch from the reluctor ring. As the notches pass the sensor, the magnetic field is altered, producing a pulsating voltage. The ignition system will not operate if the PCM does not receive a crankshaft position sensor input. When replacing the sensor, the PCM must be reprogrammed using special equipment and a crankshaft sensor variation relearn procedure must be performed using a special TECH 2 scan tool. This should be done by a dealer service department or other qualified automotive repair facility. To replace the sensor, disconnect the cable from the negative battery terminal, raise the vehicle and support it securely on jackstands, disconnect the electrical connector from the sensor, remove the sensor mounting bolt and the sensor itself. Installation is the reverse of removal.

Genuine Chevrolet Trailblazer Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Crankshaft Position Sensors found

View related parts
Chevrolet Trailblazer Sensor Assembly, Cr/Shf Posn
Part Number: 12703627
$49.37 MSRP: $102.52
You Save: $53.15 (52%)
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 12585546
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Trailblazer | 4 DOOR | 8 Cyl 5.3L, 8 Cyl 6.0L
View related parts
Chevrolet Trailblazer Sensor,Crankshaft Position
Part Number: 12567712
$41.61 MSRP: $86.40
You Save: $44.79 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 1103703, 24576398, 10456295
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2007 Chevrolet Trailblazer | 4 DOOR, 4 DOOR EXT | 6 Cyl 4.2L
View related parts
Chevrolet Trailblazer Sensor Assembly, Crankshaft Position
Part Number: 12597254
$26.15 MSRP: $49.34
You Save: $23.19 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chevrolet Trailblazer | 4 DOOR | 6 Cyl 4.2L
View related parts
Chevrolet Trailblazer Sensor,Crankshaft Position
Part Number: 12560228
$65.50 MSRP: $117.48
You Save: $51.98 (45%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 12555566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chevrolet Trailblazer | 4 DOOR, 4 DOOR EXT | 8 Cyl 5.3L, 8 Cyl 6.0L
View related parts
Chevrolet Trailblazer Sensor Assembly, Knock
Part Number: 12663209
$3.91 MSRP: $7.37
You Save: $3.46 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Trailblazer | 4 DOOR EXT | 3 Cyl 1.3L
View related parts
Chevrolet Trailblazer Sensor Assembly, Cr/Shf Posn
Part Number: 12706708
$6.96 MSRP: $12.48
You Save: $5.52 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 55507118
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Trailblazer | 4 DOOR EXT | 3 Cyl 1.2L, 3 Cyl 1.3L
View related parts
Chevrolet Trailblazer Sensor Assembly, Cm/Shf Posn
Part Number: 12698173
$11.81 MSRP: $22.28
You Save: $10.47 (47%)
ADD TO CART
Product Specifications
- Replaced by: 12733487
- Replaces: 55508453
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Trailblazer | 4 DOOR EXT | 3 Cyl 1.2L

Chevrolet Trailblazer Crankshaft Position Sensor

The Crankshaft Position Sensor is an important feature in the Chevrolet Trailblazer as this determine the position and speed of the vehicle crankshaft and pass this information to the powertrain control module. This information is applied in the control of ignition timing and fuel injection timing with the aim of improving on the engine's performance. It has the responsibility of regulating several parameters of an engine for example the fuel injection and ignition time for smooth running of the engine. Inductive, Hall EFFECT, magnetoresistive, and Optical sensor types may be used in Trailblazer vehicles with the strength of each type and the specific benefits it has over others. The common problem related to the crankshaft position sensor includes idle, stumbling, short-starting, and hard starting especially when the engine is hot. The sensor must be in good condition and protected and therefore any compromise to the condition of the sensor poses a danger to the good working of the vehicle.

Each OEM Chevrolet Trailblazer Crankshaft Position Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Trailblazer Crankshaft Position Sensor Parts Questions & Experts Answers

Sensor Assembly, Crankshaft Position
12597254
Q: What does the Crankshaft Position (CKP) sensor provide to the PCM?
A: The Crankshaft Position (CKP) sensor provides the PCM with a crankshaft position signal, which the PCM uses to determine the spark sequence for each cylinder, control ignition timing, and calculate engine speed. The signal is also used by the Onboard Diagnostic system for misfire detection. The sensor is triggered by slots cut into a reluctor ring on the crankshaft and is positioned approximately 0.050 inch from the reluctor ring. As the notches pass the sensor, the magnetic field is altered, producing a pulsating voltage. The ignition system will not operate if the PCM does not receive a crankshaft position sensor input. When replacing the sensor, the PCM must be reprogrammed using special equipment and a crankshaft sensor variation relearn procedure must be performed using a special TECH 2 scan tool. This should be done by a dealer service department or other qualified automotive repair facility. To replace the sensor, disconnect the cable from the negative battery terminal, raise the vehicle and support it securely on jackstands, disconnect the electrical connector from the sensor, remove the sensor mounting bolt and the sensor itself. Installation is the reverse of removal.