How do you remove the clutch master cylinder on Chevrolet S10?

To remove the clutch master cylinder, start by disconnecting the negative cable from the battery. Then, under the dash, remove the lower filler panel and the lower left air conditioning duct (if equipped). Next, disconnect the pushrod from the top of the clutch pedal, which is held in place with a spring clip. To disconnect the clutch fluid hydraulic line, drive out the roll pin holding the hydraulic tube to the master cylinder using a 7/64-inch punch. Be prepared with rags, as some fluid will be lost during this step. To detach the master cylinder from the firewall, rotate it clockwise 45-degrees. On later models with an integral fluid line, use a special tool to release the quick-connector at the clutch housing. For installation, start by attaching the master cylinder to the firewall using a new seal. Hold it at a 45-degree angle and rotate it counterclockwise, being careful not to rotate it too far to avoid damage. Use a new roll pin to connect the hydraulic fluid line to the master cylinder. On later models, connect the integral fluid line to the release master cylinder. Inside the vehicle, connect the pushrod to the clutch pedal. Then, install the lower left air conditioning duct (if equipped) and the lower filler panel. Finally, fill the clutch master cylinder reservoir with the specified fluid and bleed the clutch system.

Genuine Chevrolet S10 Clutch Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Clutch Master Cylinders found

View related parts
Chevrolet S10 Cylinder Assembly, Clutch Master
Part Number: 12574149
$138.96 MSRP: $219.63
You Save: $80.67 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 15718351, 15740927, 15051974
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2003 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Actuator Asm,Clutch
Part Number: 12385321
$136.31 MSRP: $215.44
You Save: $79.13 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: ACTUATOR, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 15998928
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Master Cylinder, Hydraulic Clutch
Part Number: 15594142
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Cylinder,Clutch Master
Part Number: 15051973
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 15153421, 15733571
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Cylinder Asm,Clutch Master
Part Number: 12385319
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Cylinder Assembly, Clutch Master
Part Number: 12584955
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 12574150, 15762468
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Repair Kit, Main Cyl
Part Number: 15579688
Product Specifications
- Other Name: CYLINDER KIT; Master Cylinder Repair Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Cylinder Asm,Clutch Master
Part Number: 12387941
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 12549134
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Master Cyl, Hydraulic Clutch(Increase Push Rod)
Part Number: 15576194
Product Specifications
- Other Name: CYLINDER, Hydraulic Clutch Main Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Actuator Asm,Clutch
Part Number: 12385317
Product Specifications
- Other Name: ACTUATOR, Hydraulic Clutch Main Cylinder; Master Cylinder
- Replaces: 15679740
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Actuator Asm,Clutch
Part Number: 12385318
Product Specifications
- Other Name: ACTUATOR, Hydraulic Clutch Main Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 6 Cyl 2.8L

Chevrolet S10 Clutch Master Cylinder

In the Chevrolet S10 vehicles, a Critical Component is the Clutch Master Cylinder since it is the one that creates hydraulic pressure to enable the engagement of the clutch when the clutch pedal is depressed. This hydraulic pressure is then transmitted to the slave cylinder so as to move a clutch and assist in the procedure of gear shift. The symptoms of Clutch Master Cylinder problem include soft pedal, fluid coming out from the cylinder, and unable to change gear smoothly. Damage in the cylinder may be due to the seals or the cylinder bores getting worn out or even other problems like rust and air get into the system. The Clutch Master Cylinder is another important component in the working of the transmission system of the vehicle and also plays a safety measure while operating the car.

Each OEM Chevrolet S10 Clutch Master Cylinder we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Clutch Master Cylinder Parts Questions & Experts Answers

Actuator Asm,Clutch
12385321
Q: How do you remove the clutch master cylinder on Chevrolet S10?
A: To remove the clutch master cylinder, start by disconnecting the negative cable from the battery. Then, under the dash, remove the lower filler panel and the lower left air conditioning duct (if equipped). Next, disconnect the pushrod from the top of the clutch pedal, which is held in place with a spring clip. To disconnect the clutch fluid hydraulic line, drive out the roll pin holding the hydraulic tube to the master cylinder using a 7/64-inch punch. Be prepared with rags, as some fluid will be lost during this step. To detach the master cylinder from the firewall, rotate it clockwise 45-degrees. On later models with an integral fluid line, use a special tool to release the quick-connector at the clutch housing. For installation, start by attaching the master cylinder to the firewall using a new seal. Hold it at a 45-degree angle and rotate it counterclockwise, being careful not to rotate it too far to avoid damage. Use a new roll pin to connect the hydraulic fluid line to the master cylinder. On later models, connect the integral fluid line to the release master cylinder. Inside the vehicle, connect the pushrod to the clutch pedal. Then, install the lower left air conditioning duct (if equipped) and the lower filler panel. Finally, fill the clutch master cylinder reservoir with the specified fluid and bleed the clutch system.