How to remove and install brake calipers?

Dust created by the brake system is harmful to your health. Never blow it out with compressed air and don't inhale any of it. An approved filtering mask should be worn when working on the brakes. Do not, under any circumstances, use petroleum-based solvents to clean brake parts. Use brake system cleaner only. If replacement is indicated (usually because of fluid leakage), it is recommended that the calipers be replaced, not overhauled. New and factory rebuilt units are available on an exchange basis, which makes this job quite easy. Always replace the calipers in pairs-never replace just one of them. This procedure applies to front and rear disc brakes. Removal: Loosen the wheel lug nuts, raise the end of the vehicle you're working on and support it securely on jack stands. Block the wheels at the opposite end. Remove the wheels. Depress the caliper piston with a C-clamp just enough to allow the pad to clear the disc (On front brakes and rear brakes with parking brake shoes (instead of actuator-type calipers), depress the caliper pistons into the bottom of their bores with a large C-clamp). Caution: Do not attempt to depress the piston into the caliper on later models with parking brake actuator-type calipers. Disconnect the brake line from the caliper and plug it to keep contaminants out of the brake system and to prevent losing any more brake fluid than is necessary (Brake caliper mounting details: Brake line fitting Caliper mounting bolts Caliper mounting bracket bolts). Note: If you're simply removing the caliper for access to other components, don't disconnect the brake line from the caliper. Remove the caliper mounting bolts (or guide pins on rear calipers). Note: On front calipers, hold the guide pin with a wrench to remove the mounting bolts (Hold the guide pin with one wrench while removing the lower caliper mounting bolt with another). Detach the caliper from its mounting bracket. Installation: Install the caliper by reversing the removal procedure. Remember to replace the copper sealing washers on either side of the brake line fitting with new ones. Tighten the caliper mounting bolts and the brake line banjo fitting bolt to the torque. Bleed the brake system. Install the wheels and lug nuts and lower the vehicle. Tighten the wheel lug nuts to the torque. Check the operation of the brakes thoroughly before placing the vehicle into normal service.

Genuine Chevrolet Monte Carlo Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Brake Calipers found

View related parts
Chevrolet Monte Carlo Caliper Asm,Front Brake
Part Number: 18060106
$128.98 MSRP: $254.46
You Save: $125.48 (50%)
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18015174
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Asm,Front Brake (Service)
Part Number: 18046196
$143.26 MSRP: $284.26
You Save: $141.00 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18029818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Asm,Rear Brake
Part Number: 88962832
$169.68 MSRP: $291.12
You Save: $121.44 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18029825, 18021113
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Asm,Rear Brake
Part Number: 88965667
$73.86 MSRP: $231.41
You Save: $157.55 (69%)
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18029936
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Caliper Kit,Rear Brake
Part Number: 18023387
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Asm,Front Brake (Service)
Part Number: 18046197
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18029819
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Kit,Front Brake
Part Number: 18015169
Product Specifications
- Other Name: Overhaul Kit; Caliper Overhaul Kit
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Kit,Front Brake
Part Number: 18017156
Product Specifications
- Other Name: CALIPER KIT; Caliper Overhaul Kit, Overhaul Kit
- Position: Front
- Replaces: 18024958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Kit,Rear Brake Repair
Part Number: 18029823
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper,Front Brake (LH)
Part Number: 18015427
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1988 Chevrolet Monte Carlo | EL CAMINO, MONTE CARLO | 6 Cyl 4.3L, 8 Cyl 5.0L
View related parts
Chevrolet Monte Carlo Caliper Asm,Rear Brake
Part Number: 88965666
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18029935
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | IMPALA, LS, LT, POLICE CAR, SS | 6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.5L Flex, 6 Cyl 3.8L, 6 Cyl 3.9L, 8 Cyl 5.3L
View related parts
Chevrolet Monte Carlo Caliper Asm,Front Brake
Part Number: 18060107
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18015175
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L
View related parts
Chevrolet Monte Carlo Caliper Asm,Rear Brake
Part Number: 88962831
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18029824, 18021112
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, LS 4 DOOR, LTZ, LTZ 4 DOOR, LUMINA, MONTE CARLO, Z34 | 6 Cyl 3.1L, 6 Cyl 3.4L, 6 Cyl 3.8L

Chevrolet Monte Carlo Brake Calipers

Chevrolet Monte Carlo Brake Caliperss is extremely vital braking part, which actuates hydraulic pressure from the master cylinder and convert them into mechanical force. This force is used to push the brake pads against the rotors so as to slow down or even stop the vehicle. Monte Carlo models utilize two primary types of Brake Calipers: there are two types of shelf fitting known as, fixed and floating. They are even modern calipers used in the maturing Monte Carlo in various designs over the years, such as the performance-oriented ones that boost both the car's stopping force as well as its looks. Standard calipers are usually of cast iron construction while the pistons are made from steel or phenolic types. Performance calipers can also come in lightweight aluminum and have better additional features for better durability and enhanced performance. Continual examinations and services should be done on the Brake Caliper so as to avoid problems such as leakage, uneven wearing off, as well as brake drag.

Each OEM Chevrolet Monte Carlo Brake Calipers we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Monte Carlo Brake Calipers Parts Questions & Experts Answers

Caliper Asm,Rear Brake
88965667
Q: How to remove and install brake calipers?
A: Dust created by the brake system is harmful to your health. Never blow it out with compressed air and don't inhale any of it. An approved filtering mask should be worn when working on the brakes. Do not, under any circumstances, use petroleum-based solvents to clean brake parts. Use brake system cleaner only. If replacement is indicated (usually because of fluid leakage), it is recommended that the calipers be replaced, not overhauled. New and factory rebuilt units are available on an exchange basis, which makes this job quite easy. Always replace the calipers in pairs-never replace just one of them. This procedure applies to front and rear disc brakes. Removal: Loosen the wheel lug nuts, raise the end of the vehicle you're working on and support it securely on jack stands. Block the wheels at the opposite end. Remove the wheels. Depress the caliper piston with a C-clamp just enough to allow the pad to clear the disc (On front brakes and rear brakes with Parking Brake Shoes (instead of actuator-type calipers), depress the caliper pistons into the bottom of their bores with a large C-clamp). Caution: Do not attempt to depress the piston into the caliper on later models with parking brake actuator-type calipers. Disconnect the Brake Line from the caliper and plug it to keep contaminants out of the brake system and to prevent losing any more brake fluid than is necessary (Brake caliper mounting details: Brake line fitting Caliper mounting bolts Caliper mounting bracket bolts). Note: If you're simply removing the caliper for access to other components, don't disconnect the brake line from the caliper. Remove the caliper mounting bolts (or guide pins on rear calipers). Note: On front calipers, hold the guide pin with a wrench to remove the mounting bolts (Hold the guide pin with one wrench while removing the lower caliper mounting bolt with another). Detach the caliper from its mounting bracket. Installation: Install the caliper by reversing the removal procedure. Remember to replace the copper sealing washers on either side of the brake line fitting with new ones. Tighten the caliper mounting bolts and the brake line banjo fitting bolt to the torque. Bleed the brake system. Install the wheels and lug nuts and lower the vehicle. Tighten the wheel lug nuts to the torque. Check the operation of the brakes thoroughly before placing the vehicle into normal service.

Related Chevrolet Monte Carlo Parts

Browse by Year

2007 Brake Calipers 2006 Brake Calipers 2005 Brake Calipers 2004 Brake Calipers 2003 Brake Calipers 2002 Brake Calipers 2001 Brake Calipers 2000 Brake Calipers 1999 Brake Calipers 1998 Brake Calipers 1997 Brake Calipers 1996 Brake Calipers 1995 Brake Calipers 1988 Brake Calipers 1987 Brake Calipers 1986 Brake Calipers