How do I remove and install a master cylinder?

To remove the brake master cylinder, start by locating it in the engine compartment on the left side. If necessary, remove the air filler housing that may obstruct its removal. Use a syringe or turkey baster to remove as much fluid as possible from the reservoir. Disconnect the cable from the negative battery terminal and unplug the fluid level sensor switch connector. Place rags under the line fittings and prepare caps or plastic bags to cover the ends of the lines once they're disconnected. Loosen the fittings at the ends of the brake lines using a flare-nut wrench to prevent rounding off the flats on the fittings. Pull the brake lines away from the brake master cylinder and plug the ends to prevent contamination. Finally, remove the two mounting nuts and detach the brake master cylinder from the vehicle. For installation, bench bleed the new brake master cylinder before installing it. Mount the brake master cylinder in a vise and attach a pair of brake master cylinder bleeder tubes to the outlet ports. Fill the reservoir with the recommended brake fluid and slowly push the pistons into the brake master cylinder using a large Phillips screwdriver to expel air from the pressure chambers into the reservoir. Repeat this procedure until no more air bubbles are present. Remove the bleed tubes one at a time and install plugs in the open ports to prevent fluid leakage and air from entering. Install the reservoir cap. Then, install the brake master cylinder over the studs on the power brake booster and tighten the attaching nuts finger tight. Thread the brake line fittings into the brake master cylinder, ensuring not to strip the threads. Tighten the mounting nuts securely, followed by the brake line fittings. Fill the brake master cylinder reservoir with fluid and bleed the brake master cylinder and the brake system. To bleed the brake master cylinder on the vehicle, have an assistant depress the brake pedal and hold it to the floor while loosening the fitting nut to allow air and fluid to escape. Repeat this procedure on both fittings at the brake master cylinder until the fluid is clear of air bubbles. Finally, test the operation of the brake system carefully before placing the vehicle into normal service.

Genuine Cadillac Seville Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Master Cylinders found

View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 18060170
$100.99 MSRP: $236.29
You Save: $135.30 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Cadillac Seville | SEVILLE | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Repair Kit, Brake Mast Cyl
Part Number: 18007935
Product Specifications
- Other Name: CYLINDER KIT, Brake Master Cylinder; Master Cylinder Repair Kit, Overhaul Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Cadillac Seville | SEVILLE | 6 Cyl 4.1L, 8 Cyl 4.1L, 8 Cyl 5.7L Diesel
View related parts
Cadillac Seville Cylinder,Brake Master
Part Number: 18013426
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1984 Cadillac Seville | SEVILLE | 6 Cyl 4.1L, 8 Cyl 4.1L, 8 Cyl 5.7L Diesel
View related parts
Cadillac Seville Repair Kit,Brake Master Cylinder
Part Number: 18019234
Product Specifications
- Other Name: CYLINDER KIT, Brake Master Cylinder; Master Cylinder Repair Kit, Overhaul Kit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1994 Cadillac Seville | 4 DOOR, SEVILLE | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 19209230
Product Specifications
- Other Name: Master Cylinder; Master Cylinder Assembly
- Replaces: 18046507, 18044394, 18029946
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Cadillac Seville | SEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 19209215
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18021862, 18029759, 18029856, 18020057
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Cadillac Seville | 4 DOOR, DEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 19209255
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18048572
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004 Cadillac Seville | DEVILLE, HIGH LUXURY, TOURING 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder,Brake Master
Part Number: 25676067
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2003 Cadillac Seville | SEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 19209195
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Replaces: 15224504, 18046509
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Assembly, Brake Master
Part Number: 25648312
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2003 Cadillac Seville | SEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 18060148
Product Specifications
- Other Name: CYLINDER, Brake Master; Master Cylinder
- Replaces: 18016545
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac Seville | SEVILLE | 8 Cyl 4.9L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 18060179
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Replaces: 18020390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Cadillac Seville | 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Cylinder Asm,Brake Master
Part Number: 18060164
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1994 Cadillac Seville | 4 DOOR, SEVILLE | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Cylinder, Brake Master(Less Valve Block)
Part Number: 25535706
Product Specifications
- Other Name: CYLINDER, Brake Master Cylinder; Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 Cadillac Seville | SEVILLE | 8 Cyl 4.5L

Cadillac Seville Brake Master Cylinder

Each OEM Cadillac Seville Brake Master Cylinder we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Cadillac Seville Brake Master Cylinder Parts Questions & Experts Answers

Cylinder Kit,Brake Master
18022002
Q: How do I remove and install a master cylinder?
A: To remove the brake master cylinder, start by locating it in the engine compartment on the left side. If necessary, remove the air filler housing that may obstruct its removal. Use a syringe or turkey baster to remove as much fluid as possible from the reservoir. Disconnect the cable from the negative battery terminal and unplug the fluid level sensor switch connector. Place rags under the line fittings and prepare caps or plastic bags to cover the ends of the lines once they're disconnected. Loosen the fittings at the ends of the Brake Lines using a flare-nut wrench to prevent rounding off the flats on the fittings. Pull the brake lines away from the brake master cylinder and plug the ends to prevent contamination. Finally, remove the two mounting nuts and detach the brake master cylinder from the vehicle. For installation, bench bleed the new brake master cylinder before installing it. Mount the brake master cylinder in a vise and attach a pair of brake master cylinder bleeder tubes to the outlet ports. Fill the reservoir with the recommended brake fluid and slowly push the pistons into the brake master cylinder using a large Phillips screwdriver to expel air from the pressure chambers into the reservoir. Repeat this procedure until no more air bubbles are present. Remove the bleed tubes one at a time and install plugs in the open ports to prevent fluid leakage and air from entering. Install the reservoir cap. Then, install the brake master cylinder over the studs on the power Brake Booster and tighten the attaching nuts finger tight. Thread the brake line fittings into the brake master cylinder, ensuring not to strip the threads. Tighten the mounting nuts securely, followed by the brake line fittings. Fill the brake master cylinder reservoir with fluid and bleed the brake master cylinder and the brake system. To bleed the brake master cylinder on the vehicle, have an assistant depress the brake pedal and hold it to the floor while loosening the fitting nut to allow air and fluid to escape. Repeat this procedure on both fittings at the brake master cylinder until the fluid is clear of air bubbles. Finally, test the operation of the brake system carefully before placing the vehicle into normal service.

Related Cadillac Seville Parts

Browse by Year