How to inspect and replace flexible hoses?

To inspect and replace flexible hoses, start by raising the vehicle and securely supporting it on jackstands. Thoroughly check the hoses for cracks, chafing, leaks, blisters, and other damage. Use a light and mirror to see into restricted areas. If any hose exhibits these conditions, replace it with a new one. To disconnect the brake line from the hose fitting, use an open-end wrench on the hose fitting and a flare-nut wrench on the line fitting, being careful not to bend the frame bracket or brake line. Remove the U-clip from the female fitting at the bracket using pliers, then remove the hose from the bracket. At the caliper end of the hose, remove the bolt from the fitting block and take off the hose and copper gaskets on either side of the fitting block. When installing the hose, always use new copper gaskets and lubricate all bolt threads with clean brake fluid. Attach the hose to the caliper with the fitting flange engaged with the caliper locating ledge. Install the female fitting in the hose bracket without twisting the hose. Use the U-clip to retain the female fitting to the frame bracket. Attach the brake line to the hose fitting and tighten the fitting using two wrenches. Ensure there are no kinks in the hose and that it doesn't contact any part of the suspension. Check this by turning the wheels to extreme left and right positions. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes before driving in traffic. When replacing metal brake lines, ensure you purchase the correct replacement parts and avoid using copper or any other tubing. Prefabricated brake lines of various lengths can be bent with a tubing bender. When installing the new line, make sure it is securely supported in the brackets with sufficient clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes before driving in traffic.

Genuine Cadillac Seville Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

46 Brake Lines found

View related parts
Cadillac Seville Hose Asm,Front Brake
Part Number: 19366748
$43.34 MSRP: $78.80
You Save: $35.46 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,FRT BRK; Flex Hose
- Position: Front
- Replaces: 22163944, 25724248
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville HOSE ASM,FRT BRK
Part Number: 19366747
$42.52 MSRP: $80.23
You Save: $37.71 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Flex Hose
- Replaces: 25724247, 22163945
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Hose Asm,Rear Brake
Part Number: 19173566
$12.78 MSRP: $22.92
You Save: $10.14 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose, Hose, Rear Flex Hose
- Position: Rear
- Replaces: 18032314, 17985580
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Hose Asm,Rear Brake
Part Number: 18032312
$12.98 MSRP: $23.28
You Save: $10.30 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose, Hose, Rear Flex Hose
- Position: Rear
- Replaces: 19173564
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Hose Asm,Rear Brake
Part Number: 18032157
$13.08 MSRP: $23.45
You Save: $10.37 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Flex Hose
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Hose Asm,Front Brake
Part Number: 19173614
$20.23 MSRP: $36.29
You Save: $16.06 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose, Front Flex Hose, Hose
- Position: Front
- Replaces: 22112116, 18032366
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Hose Asm,Front Brake
Part Number: 19173613
$22.78 MSRP: $40.87
You Save: $18.09 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Front Flex Hose, Hose
- Position: Front
- Replaces: 18032365
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Hose Asm,Front Brake
Part Number: 18032155
$24.90 MSRP: $44.66
You Save: $19.76 (45%)
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake
- Position: Front
- Replaces: 17982337
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L
View related parts
Cadillac Seville Hose Asm,Front Brake
Part Number: 19173565
$25.88 MSRP: $46.42
You Save: $20.54 (45%)
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose, Front Flex Hose, Hose
- Position: Front
- Replaces: 18032313, 17982338
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L
View related parts
Cadillac Seville Hose, Brake Master Cylinder Low Pressure
Part Number: 25528398
$37.14
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Lower Pressure Hose, Pressure Hose
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 Cadillac Seville | SEVILLE | 8 Cyl 4.5L
View related parts
Cadillac Seville Hose, Brake Pressure Mod Valve
Part Number: 3530500
$14.00
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1994 Cadillac Seville | 4 DOOR, SEVILLE | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Pipe Assembly, Brake Pressure Mod Valve Rear
Part Number: 25698855
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Cadillac Seville | DEVILLE, HIGH LUXURY, SEVILLE, SLS, STS, TOURING 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Pipe Assembly, Brake Pressure Mod Valve Front *Purple
Part Number: 25698848
$64.99 MSRP: $116.58
You Save: $51.59 (45%)
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Cadillac Seville | DEVILLE, HIGH LUXURY, TOURING 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville HOSE, Hydraulic Brake
Part Number: 22163403
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Seville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE, Hydraulic Brake
Part Number: 25664173
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Seville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE, Hydraulic Brake
Part Number: 25672093
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Seville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE, Hydraulic Brake
Part Number: 25672094
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Seville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE
Part Number: 25684555
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Cadillac Seville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE, Hydraulic Brake
Part Number: 25685528
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Cadillac Seville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville PIPE, Hydraulic Brake
Part Number: 3539643
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Cadillac Seville | 4 DOOR | 8 Cyl 4.6L

| Page 1 of 3 |Next >

1-20 of 46 Results

Cadillac Seville Brake Line Parts Questions & Experts Answers

Hose Assembly, Rear Brake (Right)
17999968
Q: How to inspect and replace flexible hoses?
A: To inspect and replace flexible hoses, start by raising the vehicle and securely supporting it on jackstands. Thoroughly check the hoses for cracks, chafing, leaks, blisters, and other damage. Use a light and mirror to see into restricted areas. If any hose exhibits these conditions, replace it with a new one. To disconnect the brake line from the hose fitting, use an open-end wrench on the hose fitting and a flare-nut wrench on the line fitting, being careful not to bend the frame bracket or brake line. Remove the U-clip from the female fitting at the bracket using pliers, then remove the hose from the bracket. At the caliper end of the hose, remove the bolt from the fitting block and take off the hose and copper gaskets on either side of the fitting block. When installing the hose, always use new copper gaskets and lubricate all bolt threads with clean brake fluid. Attach the hose to the caliper with the fitting flange engaged with the caliper locating ledge. Install the female fitting in the hose bracket without twisting the hose. Use the U-clip to retain the female fitting to the frame bracket. Attach the brake line to the hose fitting and tighten the fitting using two wrenches. Ensure there are no kinks in the hose and that it doesn't contact any part of the suspension. Check this by turning the wheels to extreme left and right positions. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes before driving in traffic. When replacing metal brake lines, ensure you purchase the correct replacement parts and avoid using copper or any other tubing. Prefabricated brake lines of various lengths can be bent with a tubing bender. When installing the new line, make sure it is securely supported in the brackets with sufficient clearance from moving or hot components. After installation, check the master cylinder fluid level, add fluid if necessary, bleed the brake system, and test the brakes before driving in traffic.