How do you remove and install Brake Calipers?

To remove the front brakes, start by loosening the lug nuts on the front wheels, but don't remove them completely. Then, raise the front of your ride and secure it on jackstands. Remove the front wheels and wash the brake assembly with brake system cleaner. Disconnect the brake line from the caliper and plug it to avoid contaminants entering the brake system hence minimizing loss of brake fluid. Next, remove the caliper mounting bolts and detach the caliper from its mounting bracket. To install new brakes on your vehicle's front, reverse removal of all components taken out ensuring that you replace sealing washers placed either side of a new fitting of a break line as well. Tighten banjo bolt along with caliper mounting bolts as per torque specifications.Thereafter,you will need to bleed your automotive braking system,mounting back tires together with lug nuts then lower down your car .Fasten lug nuts in compliance with their set torque specification while at this juncture.lowering is performed after installing wheel lugs while tightening them up properly.If you are considering rear brakes, follow a similar process.Firstly,don't forget to loosen up lug nuts on back wheels,later raise down rear side of your automobile which is then secured using jack stands.Remove rear wheels without forgetting to disengage parking brakes.dissemble brake lever by disconnecting parking cable then release it from bracket provided inside calliper.Unscrew banjo bolt then unplug fitting located at end point in order to prevent leakage because this may lead to contamination.Finally,take away caliper's mounting bolt sliding it off upper guide pin.To install new brakes you should adhere to an installation process that is opposite to removing so that sealing washer for threaded junction between line and clamp is tightened.Banjo bolt as well as caliper functional components must be fastened firmly when compared to other parts such as those in pistons.Carry out bleeding process across entire system where afterward wheels are installed on rims and lug nuts fastened before vehicle is allowed to descend as you tighten its lugs accordingly.The above procedures must be replicated while attending to the rear brakes.

Genuine Cadillac Seville Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Brake Calipers found

View related parts
Cadillac Seville Caliper Assembly, Front Brake
Part Number: 25846386
$97.48 MSRP: $193.42
You Save: $95.94 (50%)
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaced by: 87859910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Assembly, Front Brake
Part Number: 25846387
$130.27 MSRP: $233.19
You Save: $102.92 (45%)
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaced by: 87859911
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper,Front Brake
Part Number: 18046193
$88.98 MSRP: $260.40
You Save: $171.42 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 Cadillac Seville | SEVILLE, SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Kit,Rear Brake
Part Number: 18048081
$40.51 MSRP: $80.36
You Save: $39.85 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper,Rear Brake
Part Number: 18048080
$188.97 MSRP: $343.58
You Save: $154.61 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Asm,Front Brake (Service)
Part Number: 18046196
$143.26 MSRP: $284.26
You Save: $141.00 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Replaces: 18029818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Cadillac Seville | 4 DOOR, DEVILLE, HIGH LUXURY, SEVILLE, STS, TOURING 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Asm,Front Brake (W/O Brake Pads) (Remanufacture)
Part Number: 19140966
$49.77 MSRP: $91.20
You Save: $41.43 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Replaces: 18036581
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Caliper Asm,Rear Brake
Part Number: 88962835
$54.03 MSRP: $248.03
You Save: $194.00 (79%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Replaces: 18040792
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac Seville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Kit,Rear Brake
Part Number: 18042415
$24.38 MSRP: $63.64
You Save: $39.26 (62%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | DEVILLE, HIGH LUXURY, SEVILLE, SLS, STS, TOURING 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Kit,Rear Brake
Part Number: 18040086
Product Specifications
- Other Name: CALIPER KIT, Wheel Cylinder Piston; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2002 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Asm,Rear Brake (Service)
Part Number: 18048079
$191.53 MSRP: $343.58
You Save: $152.05 (45%)
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Seville | DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville CALIPER
Part Number: 88962836
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac Seville | SLS, STS | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Kit,Front Brake
Part Number: 18017156
Product Specifications
- Other Name: CALIPER KIT; Caliper Overhaul Kit, Overhaul Kit
- Position: Front
- Replaces: 18024958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2004 Cadillac Seville | 4 DOOR, DEVILLE, HIGH LUXURY, SEVILLE, SLS, STS, TOURING 4 DOOR | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Caliper Kit,Rear Brake Repair
Part Number: 18029823
Product Specifications
- Other Name: CALIPER KIT, Wheel Brake Cylinder/Caliper; Caliper Overhaul Kit, Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Cadillac Seville | 4 DOOR, DEVILLE, SEVILLE, SLS, STS | 8 Cyl 4.6L, 8 Cyl 4.9L
View related parts
Cadillac Seville Caliper Asm,Rear Brake (W/0 Brake Pads) (Remanufacture)
Part Number: 19141043
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Rear
- Replaces: 18012692, 18060067, 18036728
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Caliper Assembly Pkg, Right
Part Number: 18012691
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | SEVILLE | 8 Cyl 4.1L, 8 Cyl 4.5L, 8 Cyl 4.9L
View related parts
Cadillac Seville Caliper,Front Brake
Part Number: 18014745
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Cadillac Seville | 4 DOOR, DEVILLE | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Asm,Front Brake (Service)
Part Number: 18029937
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Seville | 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Asm,Front Brake (Service)
Part Number: 18029938
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper, Caliper Assembly
- Position: Front
- Replaces: 18029929, 18021252
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Cadillac Seville | 4 DOOR | 8 Cyl 4.6L
View related parts
Cadillac Seville Caliper Assembly, Rear Brake
Part Number: 18017425
Product Specifications
- Other Name: CALIPER, Wheel Brake Cylinder/Caliper; Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | SEVILLE | 8 Cyl 4.9L

| Page 1 of 2 |Next >

1-20 of 33 Results

Cadillac Seville Brake Calipers Parts Questions & Experts Answers

Caliper Kit,Rear Brake
18040086
Q: How do you remove and install Brake Calipers?
A: To remove the front brakes, start by loosening the lug nuts on the front wheels, but don't remove them completely. Then, raise the front of your ride and secure it on jackstands. Remove the front wheels and wash the brake assembly with brake system cleaner. Disconnect the Brake Line from the caliper and plug it to avoid contaminants entering the brake system hence minimizing loss of brake fluid. Next, remove the caliper mounting bolts and detach the caliper from its mounting bracket. To install new brakes on your vehicle's front, reverse removal of all components taken out ensuring that you replace sealing washers placed either side of a new fitting of a break line as well. Tighten banjo bolt along with caliper mounting bolts as per torque specifications.Thereafter,you will need to bleed your automotive braking system,mounting back tires together with lug nuts then lower down your car .Fasten lug nuts in compliance with their set torque specification while at this juncture.lowering is performed after installing wheel lugs while tightening them up properly.If you are considering rear brakes, follow a similar process.Firstly,don't forget to loosen up lug nuts on back wheels,later raise down rear side of your automobile which is then secured using jack stands.Remove rear wheels without forgetting to disengage parking brakes.dissemble brake lever by disconnecting parking cable then release it from bracket provided inside calliper.Unscrew banjo bolt then unplug fitting located at end point in order to prevent leakage because this may lead to contamination.Finally,take away caliper's mounting bolt sliding it off upper guide pin.To install new brakes you should adhere to an installation process that is opposite to removing so that sealing washer for threaded junction between line and clamp is tightened.Banjo bolt as well as caliper functional components must be fastened firmly when compared to other parts such as those in pistons.Carry out bleeding process across entire system where afterward wheels are installed on rims and lug nuts fastened before vehicle is allowed to descend as you tighten its lugs accordingly.The above procedures must be replicated while attending to the rear brakes.

Related Cadillac Seville Parts

Browse by Year

2004 Brake Calipers 2003 Brake Calipers 2002 Brake Calipers 2001 Brake Calipers 2000 Brake Calipers 1999 Brake Calipers 1998 Brake Calipers 1997 Brake Calipers 1996 Brake Calipers 1995 Brake Calipers 1994 Brake Calipers 1993 Brake Calipers 1992 Brake Calipers 1991 Brake Calipers 1990 Brake Calipers 1989 Brake Calipers 1988 Brake Calipers 1987 Brake Calipers 1986 Brake Calipers