What are the steps involved in valve reconditioning procedures?

Valve resurfacing involves a sequence of activities that are different for various engine types. First, remove the cylinder head and place it on a clean, well-lit work surface. Eliminate valve seals from intake valve guides and discard them. Get rid of the valves and number them for reinstallation purposes. Make sure to cleanse all carbon deposits from combustion chambers, piston crowns and valves with a soft wire brush being careful not to rasp against valve seats or faces. Using the right spring compressor for valves, compress the valve spring until it springs off its cap keys. Free it in order to get rid of this cap. Cleaning carbon and gum deposits out of valve guide bores may be done using Reamer J-8101. The pits or damages on the valve faces as well as seat require attention therefore reface them at 45° angle if necessary. When there is excessive clearance with either 0.006 or 0.010 reamers ,ream out valve guides lightly lap valves into seats with fine grinding compound , ensuring smooth and true surfaces Test each one using Prussian blue coated on the face of each other to see who is more concentrically aligned Remove burrs from stem ends, polish stems with crocus cloth, lubricate stems and guides with clean engine oil before putting back Install new intake seals (no exhaust seal needed). Use an installer to locate these seals above guides correctly Install such springs so that tightly wound coil is located next to cylinder head (on 8-350 exhale ones you can install any end up) Pressurize springs then return caps afterwards assembling cylinder heads again Start by taking off rocker arm nuts balls arms use a compressor for removing keepers caps other relevant pieces when dealing Chevrolet engines For Pontiac motors remove rocker arms employing a compressor which removes locks caps among others in addition to this Restore Oldsmobile engines have remover key oil seals followed by their respective valves New oil seals are put over stems by means of an appropriate tool for the purpose Narrow valve seats to specified width and if necessary ream out guide bores for oversize valves when reconditioning the valves as well as valve seats This might be carbon deposits narrowing or widening a valve seat stem height and clearance etcetera assess wear, damage or any other problems from different parts. Valving conditions require scrutinizing for various components such as wear, damages, problems and others that may arise hence follow manufacturer's guidelines on servicing valves Measure correctly the height of each stem after proper placement of keys by tapping it down. Take all valves' measurements to ensure correct stem heights, replacing those ones that went too short.

Genuine Buick Century Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Intake Valves found

View related parts
Buick Century Valve, Intake
Part Number: 10166341
$19.28 MSRP: $23.65
You Save: $4.37 (19%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Buick Century | CUSTOM, CUSTOM STATION WAGON, GS, LIMITED, LS, REGAL, SPECIAL, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 6 Cyl 3.1L
View related parts
Buick Century Valve, Intake
Part Number: 10040226
$13.05 MSRP: $18.51
You Save: $5.46 (30%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century Valve, Inlet
Part Number: 25512098
$13.15 MSRP: $26.53
You Save: $13.38 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: VALVE, Intake; Intake Valve, Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 6 Cyl 3.0L, 6 Cyl 3.8L
View related parts
Buick Century Valve, Intake(.089 Oversize)
Part Number: 10166374
$16.72 MSRP: $33.70
You Save: $16.98 (51%)
ADD TO CART
Product Specifications
- Other Name: VALVE, Intake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Century | CUSTOM, GS, LIMITED, LS, REGAL | 6 Cyl 3.1L
- 1994-1995 Buick Century | CUSTOM, CUSTOM STATION WAGON, SPECIAL, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 6 Cyl 3.1L
View related parts
Buick Century Valve, Intake
Part Number: 24501290
$12.16 MSRP: $19.40
You Save: $7.24 (38%)
ADD TO CART
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 6 Cyl 3.3L
View related parts
Buick Century Valve,Intake
Part Number: 24506031
$15.74 MSRP: $26.05
You Save: $10.31 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: VALVE, Intake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Century | CUSTOM, CUSTOM 4 DOOR, GL, GLX, GS, LIMITED, LS | 6 Cyl 3.1L
View related parts
Buick Century Valve,Intake
Part Number: 12616697
$23.79 MSRP: $37.44
You Save: $13.65 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: VALVE, Intake; Intake Valve, Valve
- Replaces: 24505722, 12569583
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Century | CUSTOM, CUSTOM 4 DOOR, GL, GLX, GS, LIMITED, LS | 6 Cyl 3.1L
View related parts
Buick Century Valve,Intake
Part Number: 10198816
$8.55 MSRP: $21.74
You Save: $13.19 (61%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: VALVE, Intake; Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Buick Century | CUSTOM, CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 4 Cyl 2.2L
View related parts
Buick Century VALVE, Intake
Part Number: 10022882
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1986 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century VALVE, Intake
Part Number: 10044513
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century VALVE, Intake
Part Number: 10121099
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century VALVE, Intake
Part Number: 12353400
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century VALVE, Intake
Part Number: 14024249
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 6 Cyl 2.8L
View related parts
Buick Century VALVE
Part Number: 22513937
Product Specifications
- Other Name: VALVE, Intake; Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 6 Cyl 4.3L Diesel
View related parts
Buick Century VALVE, Intake
Part Number: 24501717
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 6 Cyl 3.3L
View related parts
Buick Century Valve, Intake
Part Number: 10044512
Product Specifications
- Other Name: Intake Valve, Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR, SPECIAL 4 DOOR | 4 Cyl 2.5L
View related parts
Buick Century Valve,Intake, .015 Os
Part Number: 12353404
Product Specifications
- Other Name: VALVE, Intake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 6 Cyl 3.3L
View related parts
Buick Century Valve, Intake
Part Number: 14091805
Product Specifications
- Other Name: Intake Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1989 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 2 DOOR, LIMITED 4 DOOR | 6 Cyl 2.8L
View related parts
Buick Century Valve, Inlet(0.150Mm Oversize)
Part Number: 10156074
Product Specifications
- Other Name: VALVE, Intake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 4 Cyl 2.2L
View related parts
Buick Century Valve, Inlet(0.300Mm Oversize)
Part Number: 10156076
Product Specifications
- Other Name: VALVE, Intake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Buick Century | CUSTOM 2 DOOR, CUSTOM 4 DOOR, CUSTOM STATION WAGON, LIMITED 4 DOOR, SPECIAL 4 DOOR, SPECIAL STATION WAGON | 4 Cyl 2.2L

| Page 1 of 2 |Next >

1-20 of 23 Results

Buick Century Intake Valve

The Intake Valve within Buick Century cars helps to increase the engine power and combustion chamber efficiency because of the control of the air and fuel combinations. Inability to perform to the required standards often results from failure of these valves in the engine. Intake valves should be replaced with precision since the process entails the use of particular tools and a specific procedure that would not allow further Issuance of an engine. Therefore, if the steps mentioned above are strictly adhered to, you will be able to replace intake valves and main an efficient and well-running engine. Subsequently, during replacement, much attention should be paid to the particularities that could lead to valve damage or looseness.

Each OEM Buick Century Intake Valve we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Buick Century Intake Valve Parts Questions & Experts Answers

VALVE, Intake
10022882
Q: What are the steps involved in valve reconditioning procedures?
A: Valve resurfacing involves a sequence of activities that are different for various engine types. First, remove the Cylinder Head and place it on a clean, well-lit work surface. Eliminate valve seals from intake valve guides and discard them. Get rid of the valves and number them for reinstallation purposes. Make sure to cleanse all carbon deposits from combustion chambers, piston crowns and valves with a soft wire brush being careful not to rasp against valve seats or faces. Using the right spring compressor for valves, compress the valve spring until it springs off its cap keys. Free it in order to get rid of this cap. Cleaning carbon and gum deposits out of valve guide bores may be done using Reamer J-8101. The pits or damages on the valve faces as well as seat require attention therefore reface them at 45° angle if necessary. When there is excessive clearance with either 0.006 or 0.010 reamers ,ream out valve guides lightly lap valves into seats with fine grinding compound , ensuring smooth and true surfaces Test each one using Prussian blue coated on the face of each other to see who is more concentrically aligned Remove burrs from stem ends, polish stems with crocus cloth, lubricate stems and guides with clean engine oil before putting back Install new intake seals (no exhaust seal needed). Use an installer to locate these seals above guides correctly Install such springs so that tightly wound coil is located next to cylinder head (on 8-350 exhale ones you can install any end up) Pressurize springs then return caps afterwards assembling cylinder heads again Start by taking off Rocker Arm nuts balls arms use a compressor for removing keepers caps other relevant pieces when dealing Chevrolet engines For Pontiac motors remove rocker arms employing a compressor which removes locks caps among others in addition to this Restore Oldsmobile engines have remover key oil seals followed by their respective valves New oil seals are put over stems by means of an appropriate tool for the purpose Narrow valve seats to specified width and if necessary ream out guide bores for oversize valves when reconditioning the valves as well as valve seats This might be carbon deposits narrowing or widening a valve seat stem height and clearance etcetera assess wear, damage or any other problems from different parts. Valving conditions require scrutinizing for various components such as wear, damages, problems and others that may arise hence follow manufacturer's guidelines on servicing valves Measure correctly the height of each stem after proper placement of keys by tapping it down. Take all valves' measurements to ensure correct stem heights, replacing those ones that went too short.