Make sure this part fits

Pontiac 88965333 Stud Kit,Front Lower Control Arm Ball

1997-2009 Pontiac

Customer Questions & Expert Answers (5)
GM 88965333 Stud Kit,Front Lower Control Arm Ball
  • Part Description
    STUD KIT, Front Wheel Lower Control Arm
  • Position
    Front Lower
  • Replaces
    88955451, 22157089
  • Manufacturer
    General Motors
Make sure this part fits
$44.20 MSRP: $76.93
You Save: $32.73 (43%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number88965333
    Part DescriptionSTUD KIT, Front Wheel Lower Control Arm
    Other NamesBall Joint, Lower Ball Joint
    Item Dimensions7.1 x 4.3 x 4.3 inches
    Item Weight1.80 Pounds
    PositionFront Lower
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces88955451, 22157089
    ManufacturerGeneral Motors
    SKU88965333
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2001-2005 Pontiac Aztek6 Cyl 3.4LAZTEK, GT AWD
    1997-2008 Pontiac Grand Prix6 Cyl 3.1L, 6 Cyl 3.8L, 8 Cyl 5.3L2 DOOR, 4 DOOR, GT 2 DOOR, GT 4 DOOR, GT2 4 DOOR, GTP 2 DOOR, GTP 4 DOOR, GXP 4 DOOR, SE 4 DOOR
    1999-2009 Pontiac Montana6 Cyl 3.4L, 6 Cyl 3.5L, 6 Cyl 3.9L, 6 Cyl 3.9L Flex2/SLIDING DOORS, CROSSOVER SPORT VAN, CROSSOVER SPORT VAN EXTENDED, EXT, EXT 2/SLIDING DOORS, MONTANA, SPECIAL 2/SLIDING DOORS
    2006-2009 Pontiac Torrent6 Cyl 3.4L, 6 Cyl 3.6LGT SUV AWD, GT SUV FWD, SUV AWD, SUV FWD
    1997-1998 Pontiac Trans Sport6 Cyl 3.4L2/SLIDING DOORS, EXT, EXT 2/SLIDING DOORS, TRANS SPORT
  • Customer Questions & Expert Answers

    Q:
    Do these parts fit my vehicle? Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 88965333 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How can you inspect and potentially replace a balljoint on Cadillac DeVille and DTS? Posted by Customer
    A:
    To inspect and potentially replace a ball joint, start by applying the parking brake and blocking the rear wheels to prevent the vehicle from rolling. Then, raise the front of the vehicle and securely support it on jack stands. Next, use a large prybar to check for any movement in the ball joint by attempting to push it up and prying it down between the steering knuckle and the control arm. Additionally, have an assistant grasp the tire at the top and bottom and move the top of the tire in and out while touching the ball joint stud nut. Finally, separate the control arm from the steering knuckle and try to twist the stud in the socket using your fingers.
    Posted by GMPartsGiant Specialist
    Q:
    How can I check the condition of the balljoint for Chevrolet Impala,Monte Carlo? Posted by Customer
    A:
    To examine the condition of the balljoint, first raise the front part of the vehicle and support it securely on jackstands. Apply the parking brake and put blocks at the rear wheels to prevent rolling. After that, make use of a prybar to check if there is increased movement between a balljoint and its steering knuckle. Moreover, let an assistant move inward and outwardly top of the tire while checking if there is any movement when testing at a stud nut. If this excessive movement occurs, then it means that the ball joint is going bad. Marking position of control arm would be a good point to start for replacing ball-joint. Then remove wheel, cotter pin and castle nut to separate ball-joint from steering knuckle. Next, take off control arm from subframe . While fixing drill out rivets used to attach old ball-joint clean up control arm and insert new one using provided fasteners . The torque for tightening these bolts should be adjusted in accordance with manufacturer's instructions . At last reattach control arm into sub-frame and secure ball stud into steering knuckle with new cotter pin applied here since old bent one must have been quite uncomfortable if not absent.
    Posted by GMPartsGiant Specialist
    Q:
    How do you remove the balljoint on the 2011 Buick LaCrosse? Posted by Customer
    A:
    First, mark the control arm's position.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ball Joint
    Q:
    What should be done after separating the balljoint from the steering knuckle of the 2005 Chevrolet Equinox? Posted by Customer
    A:
    Finally, remove the balljoint stud nut.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Ball Joint
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 88965333, the Right Choice

To ensure reliability, purchase GM part # 88965333 Stud Kit,Front Lower Control Arm Ball. It is sometimes referred to as Pontiac Ball Joint. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Pontiac Aztek, Grand Prix, Montana models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 88965333 Stud Kit,Front Lower Control Arm Ball. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly