Make sure this part fits

Pontiac 10023729 Automatic Transmission Shifter Cable Assembly

1983-1986 Pontiac

Customer Questions & Expert Answers (7)
GM 10023729 Automatic Transmission Shifter Cable Assembly
  • Part Description
    Cable Asm,Automatic Transmission Range Selector Lever
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number10023729
    Part DescriptionCable Asm,Automatic Transmission Range Selector Lever
    Item Dimensions13.7 x 13.7 x 2.4 inches
    Item Weight1.70 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU10023729
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1983-1986 Pontiac 60004 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L Diesel2 DOOR, 4 DOOR, LE 2 DOOR, LE 4 DOOR, LE STATION WAGON, SE 4 DOOR, SE STATION WAGON, STATION WAGON, STE 2 DOOR, STE 4 DOOR
    1983-1984 Pontiac Phoenix4 Cyl 2.5L, 6 Cyl 2.8L2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 10023729 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to adjust Shift Cable in a Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To begin, place the shifter in the 1st gear position. Then, remove the shifter boot and retainer at the control assembly. Install two drill bits into the alignment holes in the control assembly to hold it in 1st gear. Next, attach both shift cables to the control assembly using the studs and pin retainers, ensuring they are routed correctly and operate smoothly. Move to the transaxle and shift it into 1st gear by pushing the rail selector shaft down until you feel the resistance of the inhibitor spring, then rotate the shift lever counterclockwise. Insert the stud on the cable into the shift lever's slotted hole and tighten the retaining nut. Repeat this step for the select lever. Remove the drill bits from the control assembly and road test the car, checking for smooth shifting and engagement of each gear. Fine-tune the adjustment if necessary after the road test.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done with the transaxle for the 1983 Buick Skylark? Posted by Customer
    A:
    The transaxle should be shifted into 1st gear by pushing the rail selector shaft down until you feel the resistance of the inhibitor spring, then rotating the shift lever counterclockwise.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    What should be done after reconnecting the negative battery cable for the 1985 Buick Skylark? Posted by Customer
    A:
    Lower the car to the ground and road test, checking for a good neutral gate feel during shifting.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    What should be done at the base of the shifter for the 1981 Pontiac Phoenix? Posted by Customer
    A:
    Install a yoke clip between the tower and carrier.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    What should be reinstalled after removing the drill bit and clip of the 1984 Oldsmobile Omega? Posted by Customer
    A:
    The shifter boot and console trim plate.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    How should the shift cables be attached to the control assembly of the 1982 Oldsmobile Omega? Posted by Customer
    A:
    The shift cables should be attached to the control assembly using the studs and pin retainers, ensuring they are routed correctly and operate smoothly.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 10023729, the Right Choice

To ensure reliability, purchase GM part # 10023729 Automatic Transmission Shifter Cable Assembly. It is sometimes referred to as Pontiac Shift Cable. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Pontiac 6000, Phoenix models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 10023729 Automatic Transmission Shifter Cable Assembly. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly