Make sure this part fits

Pontiac 14080701 Automatic Transmission Shifter Cable

1982-1984 Pontiac Phoenix

Customer Questions & Expert Answers (7)
GM 14080701 Automatic Transmission Shifter Cable
  • Part Description
    Cable,Automatic Transmission Shift Control ; Cable,A/Trans Shft Cont
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Pontiac
    Manufacturer Part Number14080701
    Part DescriptionCable,Automatic Transmission Shift Control ; Cable,A/Trans Shft Cont
    Item Dimensions14.4 x 13.1 x 2.3 inches
    Item Weight1.20 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU14080701
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1982-1984 Pontiac Phoenix4 Cyl 2.5L, 6 Cyl 2.8L2 DOOR, 4 DOOR, LJ 2 DOOR, LJ 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 14080701 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to disconnect the negative battery cable and adjust the shift cable on 1981 and later Buick Skylark,Oldsmobile Omega and Pontiac Phoenix? Posted by Customer
    A:
    To disconnect the negative battery cable, shift the transaxle into 1st gear. Then, raise the front of the car and support it on jackstands. Working under the car, loosen the shift cable attaching nuts at the transaxle levers. Move to the interior of the car and remove the console trim plate, sliding the shifter boot up the shifter. Install a yoke clip between the tower and carrier at the base of the shifter, and insert a 5/32 inch or number 22 drill bit into the alignment hole at the side of the shifter assembly. Rotate the transaxle lever and tighten the attaching nut to remove slack from the cable. Tighten the attaching nut on the transaxle, then remove the drill bit and clip from the shifter assembly. Reinstall the shifter boot and console trim plate, and reconnect the negative battery cable. After adjustment, lower the car to the ground and road test, checking for a good neutral gate feel during shifting. If necessary, finer adjustments can be made after road testing.
    Posted by GMPartsGiant Specialist
    Q:
    What should be reinstalled after removing the drill bit and clip for the 1983 Buick Skylark? Posted by Customer
    A:
    The shifter boot and console trim plate.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    What should be done after connecting the shift cables for the 1985 Buick Skylark? Posted by Customer
    A:
    The drill bits should be removed from the control assembly and the car should be road tested, checking for smooth shifting and engagement of each gear.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    What should be done after reinstalling the shifter boot and console trim plate for the 1984 Pontiac Phoenix? Posted by Customer
    A:
    Reconnect the negative battery cable.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    How should the shift cables be attached to the control assembly of the 1983 Oldsmobile Omega? Posted by Customer
    A:
    The shift cables should be attached to the control assembly using the studs and pin retainers, ensuring they are routed correctly and operate smoothly.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    Q:
    Is any adjustment necessary after the road test for the 1981 Pontiac Phoenix? Posted by Customer
    A:
    If necessary, the adjustment can be fine-tuned after the road test.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Shift Cable
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 14080701, the Right Choice

To ensure reliability, purchase GM part # 14080701 Automatic Transmission Shifter Cable. It is sometimes referred to as Pontiac Shift Cable. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Pontiac Phoenix models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 14080701 Automatic Transmission Shifter Cable. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Pontiac parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly