Make sure this part fits

Oldsmobile 26064028 Seal,Differential Drive Pinion Gear

1991-2001 Oldsmobile

Customer Questions & Expert Answers (16)
GM 26064028 Seal,Differential Drive Pinion Gear
  • Part Description
    SEAL, Differential Drive Pinion Shaft Bearing
  • Manufacturer
    General Motors
Make sure this part fits
$30.33 MSRP: $50.20
You Save: $19.87 (40%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Oldsmobile
    Manufacturer Part Number26064028
    Part DescriptionSEAL, Differential Drive Pinion Shaft Bearing
    Other NamesPinion Seal
    Item Dimensions3.9 x 4.0 x 0.6 inches
    Item Weight0.50 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU26064028
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1997-2001 Oldsmobile Bravada6 Cyl 4.3LBRAVADA
    1991-1992 Oldsmobile Custom Cruiser8 Cyl 5.0L, 8 Cyl 5.7LSTATION WAGON
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 26064028 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How to remove and install a differential pinion seal on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL? Posted by Customer
    A:
    To remove and install a differential pinion seal, first loosen the wheel lug nuts and raise the front or rear of the vehicle on jackstands. Remove the wheels and disconnect the driveshaft from the differential pinion flange. Rotate the pinion and record the torque required to rotate it. Mark the relationship of the pinion flange to the shaft and count the number of exposed threads on the shaft. Use a special tool or chain wrench to immobilize the flange and remove the pinion nut. Withdraw the flange and pry out the old seal. Install the new seal by lubricating the lips and tapping it evenly into position. Apply RTV sealant to the ends of the splines visible in the center of the flange and install the washer and a new pinion nut. Tighten the nut until the recorded number of threads are exposed and measure the torque required to rotate the pinion. Tighten the nut in small increments until it matches the recorded figure and exceeds it by 5 in-lbs. Reinstall all components and tighten all fasteners to their specified torque values.
    Posted by GMPartsGiant Specialist
    Q:
    How can the pinion flange be immobilized for the 2007 Chevrolet Avalanche? Posted by Customer
    A:
    The pinion flange can be immobilized using a special tool or a chain wrench.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should be done after removing the pinion nut and companion flange for the 2001 Chevrolet Blazer? Posted by Customer
    A:
    After removing the pinion nut and companion flange, the old seal should be pried out and discarded.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What's the next step after removing the pinion nut for the 1989 Chevrolet C1500? Posted by Customer
    A:
    Withdraw the companion flange. You may need a two or three-jaw puller engaged behind the flange to draw it out.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should be done if necessary to remove the flange for the 2011 Chevrolet Colorado? Posted by Customer
    A:
    Use a two-jaw puller.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should you do after removing the wheel and accessing the front axle area for the 2012 Chevrolet Colorado? Posted by Customer
    A:
    After removing the wheel and accessing the front axle area, you should remove the splash shield from under the front axle.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    How should you tighten the pinion nut on semi-floating axles for the 1991 Chevrolet K1500? Posted by Customer
    A:
    Tighten the nut carefully until the original number of threads are exposed. Measure the torque required to rotate the pinion and tighten the nut in small increments until it matches the figure recorded earlier. In order to compensate for the drag of the new oil seal, the nut should be tightened more until the rotational torque of the pinion slightly exceeds what was recorded earlier, but not by more than 5 in-lbs.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What needs to be disconnected from the differential pinion flange for the 2005 GMC Canyon? Posted by Customer
    A:
    The driveshaft.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What is the first step to remove and install a differential pinion seal for the 2007 Chevrolet Silverado? Posted by Customer
    A:
    The first step is to loosen the wheel lug nuts and raise the front or rear of the vehicle on jackstands.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should be done before removing the pinion nut and companion flange for the 2004 Chevrolet S10? Posted by Customer
    A:
    Before removing the pinion nut and companion flange, alignment marks should be made on the pinion shaft, nut, and flange, and the number of threads visible between the nut and shaft should be counted.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What is the first step to remove and install a differential pinion seal for the 2009 GMC Sierra? Posted by Customer
    A:
    The first step is to loosen the wheel lug nuts and raise the front or rear of the vehicle on jackstands.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should be done after tightening the pinion nut for the 1996 GMC Jimmy? Posted by Customer
    A:
    After tightening the pinion nut, the driveshaft should be connected, the wheels should be installed, and the vehicle should be lowered. The lug nuts should be tightened to the proper torque.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should you do after removing the wheel and accessing the front axle area for the 2012 GMC Canyon? Posted by Customer
    A:
    After removing the wheel and accessing the front axle area, you should remove the splash shield from under the front axle.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What should be done before installing the new pinion nut for the 2011 GMC Yukon? Posted by Customer
    A:
    Before installing the new pinion nut, RTV sealant should be applied to the ends of the splines visible in the center of the flange.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    Q:
    What is the first step to remove the rear wheel for the 1998 GMC Sonoma? Posted by Customer
    A:
    The first step is to loosen the lug nuts and raise the rear of the vehicle on jackstands.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Differential Seal
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 26064028, the Right Choice

Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 26064028 Seal,Differential Drive Pinion Gear. It is sometimes referred to as Oldsmobile Differential Seal. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific Oldsmobile Bravada, Custom Cruiser models.

Affordable, reliable and built to last, GM part # 26064028 Seal,Differential Drive Pinion Gear stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed Oldsmobile parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly