How to replace a front differential seal on GMC Canyon?

Loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands and remove the wheel. Remove the splash shield from under the front axle. Remove the left driveaxle. Drain the lubricant from the front differential. Disconnect the lower stabilizer bar link from the lower control arm. Pry the seal out with a seal remover or pull it out with a slide hammer and adapter. Drive in a new seal, using a seal driver or a socket slightly smaller in diameter than the seal. Lubricate the lips of the seal with multi-purpose grease. Fill the differential with the proper lubricant. Install the driveaxle. Reconnect the lower stabilizer bar link. Install the splash shield, if equipped. Install the wheel, lower the vehicle and check for proper operation. For the left side seal, remove the driveaxle. Drain the lubricant from the front differential. Pry the Differential Seal out of the end of the axle-shaft tube with a seal remover or pull it out with a slide hammer and adapter. Drive in a new Differential Seal, using a seal driver or a socket slightly smaller in diameter than the seal. Lubricate the lips of the Differential Seal with multi-purpose grease. Reinstall the driveaxle.

How to replace a pinion seal on GMC Canyon?

Loosening the wheel lug nuts, you should raise the front or rear of the vehicle and support it securely on jackstands. Consequently, block the opposite set of wheels to prevent rolling. After that, remove the wheels. Disconnecting from the differential pinion flange, secure it out of way. Hand-rotate the pinion and use a torque wrench to measure required torque for rotation. Having marked position of the pinion flange to shaft and counted number of exposed threads. It may necessary to use special tool or chain wrench to immobilize flange and remove pinion nut. If necessary, withdraw the flange with two-jaw puller. Removing old seal, discard it; Then apply lubricate lips of new seal and fill space between lips with wheel bearing grease; After that tap new seal into position using a seal installation tool or large socket; Install pinion flange aligning marks made earlier; Apply RTV sealant to ends of splines visible in center of flange; Install washer and new pinion nut tighting until the recorded number of threads are exposed; Finally measure torque required to rotate pinion and tighten nut in small increments till it matches recorded figure; Reinstall all components, tightening all fasteners to their specified torque values.

Genuine GMC Canyon Differential Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Differential Seals found

View related parts
GMC Canyon Seal,Differential Drive Pinion Gear
Part Number: 26064029
$25.40 MSRP: $42.04
You Save: $16.64 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing; Front Seal, Pinion Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.9L, 5 Cyl 3.7L, 8 Cyl 5.3L
View related parts
GMC Canyon Seal,Differential Drive Pinion Gear
Part Number: 26064028
$30.33 MSRP: $50.20
You Save: $19.87 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing; Pinion Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.9L, 5 Cyl 3.7L
View related parts
GMC Canyon Seal,Differential Drive Pinion Gear
Part Number: 12471523
$12.61 MSRP: $23.81
You Save: $11.20 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing; Pinion Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.8L, 4 Cyl 2.9L, 5 Cyl 3.5L, 5 Cyl 3.7L
View related parts
GMC Canyon Seal,Front Differential Drive Pinion Gear
Part Number: 12479267
$13.82 MSRP: $22.03
You Save: $8.21 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing; Pinion Seal, Seal, Yoke Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | PICKUP, PICKUP CREW CAB, PICKUP EXTENDED CAB, PICKUP EXTENDED LENGTH | 4 Cyl 2.8L, 4 Cyl 2.9L, 5 Cyl 3.5L, 5 Cyl 3.7L, 8 Cyl 5.3L
View related parts
GMC Canyon Seal, Differential Drive Pinion Gear
Part Number: 84053569
$35.49 MSRP: $58.74
You Save: $23.25 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing; Pinion Seal
- Replaced by: 87861098
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | CREW CAB - 5'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L
View related parts
GMC Canyon Seal, Front Diff Drv P/Gr
Part Number: 84428304
$25.14 MSRP: $47.45
You Save: $22.31 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pinion Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB SLE -5'2" BOX, CRW CAB SPORT-5'2" BOX(I), SLT CREW CAB - 5'2" BOX, SPORT CREW-5'2" BOX | 4 Cyl 2.7L
View related parts
GMC Canyon Seal, Front Differential Drive Pinion Gear
Part Number: 84053573
$29.79 MSRP: $49.30
You Save: $19.51 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing
- Position: Front
- Replaces: 23471887
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L, 4 Cyl 2.8L Diesel, 6 Cyl 3.6L
View related parts
GMC Canyon Seal, Differential Drive Pinion Gear
Part Number: 84053572
$36.62 MSRP: $58.40
You Save: $21.78 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal, Diff Drv P/Gr; Pinion Seal
- Replaced by: 87861099
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXT CAB - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.5L, 4 Cyl 2.8L Diesel, 6 Cyl 3.6L
View related parts
GMC Canyon Seal, Differential Drive Pinion Gear
Part Number: 23490374
$36.62 MSRP: $58.40
You Save: $21.78 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Differential Drive Pinion Shaft Bearing
- Replaced by: 87861099
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | CREW CAB - 5'2" BOX, CREW CAB - 6'2" BOX, CREW CAB SLE - 6'2" BOX, CREW CAB SLT - 6'2" BOX, EXTENDED CAB - 6'2" BOX, SLE CREW CAB - 5'2" BOX, SLE EXTENDED CAB - 6'2" BOX, SLT CREW CAB - 5'2" BOX, SLT EXTENDED CAB - 6'2" BOX | 4 Cyl 2.8L Diesel, 6 Cyl 3.6L

GMC Canyon Differential Seal

Each OEM GMC Canyon Differential Seal we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Canyon Differential Seal Parts Questions & Experts Answers

Seal,Front Differential Drive Pinion Gear
12479267
Q: How to replace a front differential seal on GMC Canyon?
A: Loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands and remove the wheel. Remove the splash shield from under the front axle. Remove the left driveaxle. Drain the lubricant from the front Differential. Disconnect the lower stabilizer bar link from the lower control arm. Pry the seal out with a seal remover or pull it out with a slide hammer and adapter. Drive in a new seal, using a seal driver or a socket slightly smaller in diameter than the seal. Lubricate the lips of the seal with multi-purpose grease. Fill the differential with the proper lubricant. Install the driveaxle. Reconnect the lower stabilizer bar link. Install the splash shield, if equipped. Install the wheel, lower the vehicle and check for proper operation. For the left side seal, remove the driveaxle. Drain the lubricant from the front differential. Pry the Differential Seal out of the end of the axle-shaft tube with a seal remover or pull it out with a slide hammer and adapter. Drive in a new Differential Seal, using a seal driver or a socket slightly smaller in diameter than the seal. Lubricate the lips of the Differential Seal with multi-purpose grease. Reinstall the driveaxle.
Seal,Differential Drive Pinion Gear
26064029
Q: How to replace a pinion seal on GMC Canyon?
A: Loosening the wheel lug nuts, you should raise the front or rear of the vehicle and support it securely on jackstands. Consequently, block the opposite set of wheels to prevent rolling. After that, remove the wheels. Disconnecting from the differential pinion flange, secure it out of way. Hand-rotate the pinion and use a torque wrench to measure required torque for rotation. Having marked position of the pinion flange to shaft and counted number of exposed threads. It may necessary to use special tool or chain wrench to immobilize flange and remove pinion nut. If necessary, withdraw the flange with two-jaw puller. Removing old seal, discard it; Then apply lubricate lips of new seal and fill space between lips with wheel bearing grease; After that tap new seal into position using a seal installation tool or large socket; Install pinion flange aligning marks made earlier; Apply RTV sealant to ends of splines visible in center of flange; Install washer and new pinion nut tighting until the recorded number of threads are exposed; Finally measure torque required to rotate pinion and tighten nut in small increments till it matches recorded figure; Reinstall all components, tightening all fasteners to their specified torque values.

Related GMC Canyon Parts

Browse by Year

2024 Differential Seal 2023 Differential Seal 2022 Differential Seal 2021 Differential Seal 2020 Differential Seal 2019 Differential Seal 2018 Differential Seal 2017 Differential Seal 2016 Differential Seal 2015 Differential Seal 2012 Differential Seal 2011 Differential Seal 2010 Differential Seal 2009 Differential Seal 2008 Differential Seal 2007 Differential Seal 2006 Differential Seal 2005 Differential Seal 2004 Differential Seal