Make sure this part fits

Oldsmobile 24503787 Manifold Assembly, Vacuum Source

1994-1995 Oldsmobile Cutlass

Customer Questions & Expert Answers (9)
GM 24503787 Manifold Assembly, Vacuum Source
  • Part Description
    MANIFOLD, Intake Manifold Vacuum
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Oldsmobile
    Manufacturer Part Number24503787
    Part DescriptionMANIFOLD, Intake Manifold Vacuum
    Item Dimensions3.4 x 3.2 x 3.2 inches
    Item Weight0.80 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU24503787
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1994-1995 Oldsmobile Cutlass6 Cyl 3.4L2 DOOR, 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 24503787 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How should the fuel inlet hose be handled for the 1992 Oldsmobile Cutlass? Posted by Customer
    A:
    With a container ready to catch spillage, disconnect the fuel inlet hose at the carburetor, plugging the end to prevent dirt entry and excessive fuel seepage.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What vacuum and fuel lines need to be disconnected for the 1994 Oldsmobile Cutlass? Posted by Customer
    A:
    Disconnect the booster vacuum pipe at the manifold, the fuel line at the carburetor (plug the line and catch any spillage), the transmission vacuum modulator line if applicable, the idle stop solenoid if applicable, and the distributor wires (mark each wire with tape for ease of reassembly).
    Posted by GMPartsGiant Specialist
    Q:
    What should be done after installation for the 1993 Pontiac Grand Prix? Posted by Customer
    A:
    Finally, add coolant, run the engine, and check for leaks and proper operation.
    Posted by GMPartsGiant Specialist
    Q:
    What preparations are needed for installation for the 1998 Pontiac Grand Prix? Posted by Customer
    A:
    Ensure the mating surfaces of the cylinder heads, block, and manifold are perfectly clean, using gasket removal solvents as needed.
    Posted by GMPartsGiant Specialist
    Q:
    What is the next step after removing the oil fill tube for the 1996 Pontiac Grand Prix? Posted by Customer
    A:
    The next step is to remove the intake manifold brace, then loosen the manifold mounting nuts/bolts in 1/4-turn increments until they can be removed by hand.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What components need to be removed after the fuel rail for the 1995 Pontiac Grand Prix? Posted by Customer
    A:
    Next, remove the plenum and the radiator hose from the thermostat housing, followed by disconnecting the coolant temperature sensor and removing the heater pipe nut at the throttle body.
    Posted by GMPartsGiant Specialist
    Q:
    How should the bolts be tightened for the 1997 Pontiac Grand Prix? Posted by Customer
    A:
    Tighten the bolts in two stages following the recommended sequence.
    Posted by GMPartsGiant Specialist
    Q:
    What final checks should be performed after installation for the 1997 Pontiac Grand Prix? Posted by Customer
    A:
    Add coolant, run the engine, and check for leaks and proper operation.
    Posted by GMPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 24503787, the Right Choice

To ensure reliability, purchase GM part # 24503787 Manifold Assembly, Vacuum Source. It is sometimes referred to as Oldsmobile Intake Manifold. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Oldsmobile Cutlass models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 24503787 Manifold Assembly, Vacuum Source. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Oldsmobile parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly