Make sure this part fits

Oldsmobile 24507406 Manifold, Lower Intake

1991-1995 Oldsmobile Cutlass

Customer Questions & Expert Answers (9)
GM 24507406 Manifold, Lower Intake
  • Part Description
    MANIFOLD, Engine Fuel Intake Manifold
  • Position
    Lower
  • Replaces
    10127403
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Oldsmobile
    Manufacturer Part Number24507406
    Part DescriptionMANIFOLD, Engine Fuel Intake Manifold
    Other NamesIntake Manifold
    Item Dimensions23.0 x 8.2 x 5.7 inches
    Item Weight8.20 Pounds
    PositionLower
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces10127403
    ManufacturerGeneral Motors
    SKU24507406
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1991-1995 Oldsmobile Cutlass6 Cyl 3.4L2 DOOR, 4 DOOR, INTERNAL 2 DOOR, INTERNAL 4 DOOR
  • Customer Questions & Expert Answers

    Q:
    I would like to confirm if this is the correct part number for my vehicle. Please advise. Thank you. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 24507406 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How should the seals be installed for the 1999 Oldsmobile Cutlass? Posted by Customer
    A:
    Install new front and rear seals to the engine block using RTV or an equivalent sealant, extending the bead about One-half inch up the sides of each cylinder head to seal the side gaskets.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What preparations should be made for installation for the 1988 Pontiac Grand Prix? Posted by Customer
    A:
    For installation, ensure the mating surfaces of the cylinder head and manifold are perfectly clean, using gasket removal solvents if necessary. Remove all traces of sealant and old gasket material with a gasket scraper, then clean the surfaces with lacquer thinner or acetone.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    How do you detach the control cables for the 1992 Pontiac Grand Prix? Posted by Customer
    A:
    Detach the control cables from their brackets by pinching the tabs.
    Posted by GMPartsGiant Specialist
    Q:
    What components should be disconnected from the carburetor for the 1998 Oldsmobile Cutlass? Posted by Customer
    A:
    Disconnect the accelerator linkage at the carburetor, the linkage bracket at the manifold, and the cruise control chain if applicable.
    Posted by GMPartsGiant Specialist
    Q:
    How should the intake manifold be separated from the engine for the 1997 Pontiac Grand Prix? Posted by Customer
    A:
    Separate the intake manifold and gasket from the engine, scraping all traces of gasket material off the intake manifold and head gasket mating surfaces while being careful not to scratch or gouge the delicate aluminum surfaces.
    Posted by GMPartsGiant Specialist
    Q:
    What preparations are needed for the installation of the manifold for the 1997 Pontiac Grand Prix? Posted by Customer
    A:
    Ensure the mating surfaces of the cylinder heads, block, and manifold are perfectly clean, using gasket removal solvents as needed. Lift off the old gasket, scrape away any sealant and old gasket material, and clean the surfaces with lacquer thinner or acetone.
    Posted by GMPartsGiant Specialist
    Q:
    What components need to be removed after disconnecting the cables for the 1992 Pontiac Grand Prix? Posted by Customer
    A:
    Proceed to take off the TBI assembly and fuel lines, and if equipped, remove the power steering pump, tying it aside in an upright position.
    Posted by GMPartsGiant Specialist
    Q:
    What is the procedure for the rocker arms and pushrods for the 1989 Pontiac Grand Prix? Posted by Customer
    A:
    Loosen the rocker arm nuts/bolts, rotate the rocker arms out of the way, and remove the pushrods that go through the manifold gasket.
    Posted by GMPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 24507406, the Right Choice

To ensure reliability, purchase GM part # 24507406 Manifold, Lower Intake. It is sometimes referred to as Oldsmobile Intake Manifold. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Oldsmobile Cutlass models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 24507406 Manifold, Lower Intake. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Oldsmobile parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly