Make sure this part fits

Oldsmobile 14077854 Manifold, Center Intake

1986 Oldsmobile Cutlass

Customer Questions & Expert Answers (10)
GM 14077854 Manifold, Center Intake
  • Part Description
    MANIFOLD, Engine Fuel Intake Manifold
  • Position
    Center
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Oldsmobile
    Manufacturer Part Number14077854
    Part DescriptionMANIFOLD, Engine Fuel Intake Manifold
    Other NamesManifold
    Item Dimensions17.9 x 10.7 x 5.7 inches
    Item Weight8.40 Pounds
    PositionCenter
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU14077854
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1986 Oldsmobile Cutlass6 Cyl 2.8L2 DOOR, 4 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 14077854 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done with the vacuum lines for the 1983 Buick Skylark? Posted by Customer
    A:
    Disconnect the vacuum lines from the carburetor spacer.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done after installing the intake manifold for the 1985 Buick Skylark? Posted by Customer
    A:
    Install the remaining components in the reverse order of removal, fill the radiator with coolant, start the engine, check for leaks, and adjust the ignition timing and carburetor idle speeds as necessary.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    How should the fuel inlet hose be handled for the 1991 Oldsmobile Cutlass? Posted by Customer
    A:
    With a container ready to catch spillage, disconnect the fuel inlet hose at the carburetor, plugging the end to prevent dirt entry and excessive fuel seepage.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What additional components should be removed during the intake manifold removal process for the 1989 Pontiac Firebird? Posted by Customer
    A:
    Remove the solenoid/hose bracket, left and right rocker arm covers, upper radiator hose, heater hose, and vacuum lines from the TVS switch, along with the electrical connector from the coolant switch. Ensure all interfering wires, vacuum hoses, and coolant hoses are disconnected.
    Posted by GMPartsGiant Specialist
    Q:
    What should be done after disconnecting the battery for the 1982 Oldsmobile Cutlass? Posted by Customer
    A:
    Drain the radiator and remove the air cleaner.
    Posted by GMPartsGiant Specialist
    Q:
    How do you ensure the intake manifold gasket is properly removed for the 1985 Pontiac Fiero? Posted by Customer
    A:
    Remove the intake manifold gasket with a gasket scraper, ensuring no material remains on the mating surface.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What steps should be taken for tuned-port injected 1989 Pontiac Firebird? Posted by Customer
    A:
    Disconnect the negative battery cable, drain the coolant, and disconnect the accelerator, throttle valve, and cruise control cables. Remove the air intake duct, coolant hoses, and electrical connectors, marking them for reassembly.
    Posted by GMPartsGiant Specialist
    Q:
    What is the procedure for removing the coil for the 1986 Pontiac Firebird? Posted by Customer
    A:
    Disconnect the coil wire, remove the two retaining screws and one bolt, then take out the coil.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What components need to be reattached after the upper manifold plenum for the 1988 Pontiac Fiero? Posted by Customer
    A:
    Bolt the throttle body to the upper plenum, install the EGR pipe, and the brake booster pipe and bracket.
    Posted by GMPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 14077854, the Right Choice

To ensure reliability, purchase GM part # 14077854 Manifold, Center Intake. It is sometimes referred to as Oldsmobile Intake Manifold. Directly from GM, genuine parts are superb with regards to quality, longevity, and fit. Every single part passed stringent quality testing, so you can be sure that it's safe, durable, and built to perform like your original parts. This part fits specific Oldsmobile Cutlass models.

GMPartsGiant.com is a leading supplier of genuine GM parts and accessories such as GM 14077854 Manifold, Center Intake. You're certainly in the right place if you're searching for the great cost-effective OEM GM parts. Look no further than our vast inventory of genuine GM parts offered at unbeatable online prices, all of which are backed by the manufacturer's warranty. Not to forget, our hassle-free return policy and quick delivery service ensure a smooth shopping experience for you. For detailed Oldsmobile parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly