GMC 22761722 Seal Assembly, Front Drive Axle Inner Shaft

You can Select Your Vehicle to check if 22761722 fits your vehicle.

To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left axle shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.

To remove the oil seal from the end of the axle housing, remove the axle shaft. Then, use a pry tool to remove the oil seal. Apply a film of multi-purpose grease to the oil seal recess and install the new seal evenly with a hammer and seal installation tool. The oil seal should be aligned with the axle housing. Finally, install the axle shaft.

The first step is to remove the axle shaft.

If further disassembly of the hub is necessary, it should be done.

Install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing.

After discarding the oil seal, all components should be cleaned and inspected for wear or damage.

1. Install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. 2. Install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. 3. Carefully drive in the axle shaft with a soft-face hammer. 4. Fill the differential with the proper lubricant. 5. Install the driveaxle and differential carrier splash shield. 6. Install the wheel and lug nuts. 7. Lower the vehicle. 8. Tighten the lug nuts to the proper torque specifications. 9. Check for proper operation.

After discarding the oil seal, all components should be cleaned and inspected for wear or damage.

After cleaning and inspecting the components, the hub should be reassembled using new bearing cups and lubricating with wheel bearing grease.

1. Install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. 2. Install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. 3. Carefully drive in the axle shaft with a soft-face hammer. 4. Fill the differential with the proper lubricant. 5. Install the driveaxle and differential carrier splash shield. 6. Install the wheel and lug nuts. 7. Lower the vehicle. 8. Tighten the lug nuts to the proper torque specifications. 9. Check for proper operation.

The face of the oil seal should be flush with the end of the axle housing.

The first step is to remove the axle shaft.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.

The face of the oil seal should be flush with the end of the axle housing when correctly installed.

The lips of the seal should be facing in when installing it.

After removing the old oil seal, you should apply a film of multi-purpose grease to the oil seal recess.

1. Loosen the wheel lug nuts. 2. Raise the vehicle. 3. Place it securely on jackstands. 4. Remove the left front wheel. 5. Remove the differential carrier splash shield from under the front axle. 6. Remove the left driveaxle. 7. Drain the lubricant from the front differential. 8. Pull the left axle shaft out with a slide hammer and adapter. 9. Remove the deflector and seal from the differential. 10. Remove the bearing using a slide hammer and bearing remover attachment.

The first step is to remove the axle shaft.

The hub assembly can be removed from the axle tube by using a special socket to remove the adjusting nut and pulling the hub assembly straight off the axle tube.