How to remove and install a rear hub assembly,Wheel Bearing and Wheel Seal for Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

To remove and install a rear hub assembly, first remove the axleshaft and rear wheels, then remove the brake disc and retaining ring/key from the end of the axle housing. Use a special socket to remove the adjusting nut and pull the hub assembly straight off the axle tube. Discard the oil seal and clean and inspect all components for wear or damage. Disassemble the hub further if necessary, then clean and reassemble using new bearing cups and lubricating with wheel bearing grease. To install, place the hub assembly on the axle tube and adjust the bearings by tightening the adjusting nut to 50 ft-lbs, then backing it off and tightening it hand-tight. Install the key and retaining ring, and ensure there is no play in the hub assembly before reinstalling the axleshaft and lowering the vehicle.

How to replace and install the front Wheel Bearing and Wheel Seal of 4WD Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left axle shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.

How to replace rear oil seal from the end of an axle housing on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?

To remove the oil seal from the end of the axle housing, remove the axle shaft. Then, use a pry tool to remove the oil seal. Apply a film of multi-purpose grease to the oil seal recess and install the new seal evenly with a hammer and seal installation tool. The oil seal should be aligned with the axle housing. Finally, install the axle shaft.

Genuine Chevrolet Tahoe Wheel Seal

Wheel Axle Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Wheel Seals found

View related parts
Chevrolet Tahoe Seal Assembly, Front Drive Axle Inner Shaft
Part Number: 22761722
$20.81 MSRP: $36.23
You Save: $15.42 (43%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Axle; Output Shaft Seal
- Position: Front Inner
- Replaces: 12479012, 26059623, 12471591, 12471682, 15801507
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2020 Chevrolet Tahoe | 1500 4 DOOR UTILITY, 4 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 5.7L, 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal,Front Wheel Drive Shaft
Part Number: 19169124
$10.35 MSRP: $17.14
You Save: $6.79 (40%)
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Axle; Output Shaft Seal
- Position: Front
- Replaces: 26059624, 12471592, 12471683, 12479155
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Tahoe | CLASSIC 4 DOOR 1/2 TON
View related parts
Chevrolet Tahoe Seal,Front Wheel Inner Bearing
Part Number: 15651660
$12.60
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Wheel Bearing
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L
View related parts
Chevrolet Tahoe Seal Asm,Rear Axle Shaft
Part Number: 19180849
$14.72 MSRP: $27.78
You Save: $13.06 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SEAL, Rear Wheel Bearing Oil
- Position: Rear
- Replaces: 26057167, 14047298, 15522062
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.7L, 8 Cyl 6.5L Diesel
View related parts
Chevrolet Tahoe Seal,Rear Axle Shaft
Part Number: 12471686
$11.73 MSRP: $21.32
You Save: $9.59 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Rear Wheel Bearing Oil
- Position: Rear
- Replaces: 26037309, 15522060
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2020 Chevrolet Tahoe | 1500 4 DOOR UTILITY, 4 DOOR 1/2 TON, CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 4.8L, 8 Cyl 5.3L, 8 Cyl 5.3L Flex, 8 Cyl 5.7L, 8 Cyl 6.0L, 8 Cyl 6.0L Flex, 8 Cyl 6.2L, 8 Cyl 6.5L Diesel
View related parts
Chevrolet Tahoe Seal,Front Wheel Inner Bearing
Part Number: 15651661
$4.69 MSRP: $8.41
You Save: $3.72 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SEAL, Front Wheel Bearing
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1999 Chevrolet Tahoe | CLASSIC 4 DOOR 1/2 TON
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Shf
Part Number: 84428310
$10.22 MSRP: $19.28
You Save: $9.06 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Seal, Output Shaft Seal
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Hub (O Ring)
Part Number: 23390381
$4.46 MSRP: $8.42
You Save: $3.96 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Hub Seal, Knuckle O-Ring
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Shf
Part Number: 84392097
$4.35 MSRP: $7.20
You Save: $2.85 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Replaced by: 87862198
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Inter Shf (O, Ring)
Part Number: 23371177
$2.32 MSRP: $4.16
You Save: $1.84 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Housing O-Ring, O-Ring
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Inter Shf (O, Ring)
Part Number: 84428321
$3.57 MSRP: $6.74
You Save: $3.17 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Housing O-Ring, Inner Seal, O-Ring
- Position: Front
- Replaced by: 84983738
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Shf
Part Number: 84392096
$3.00 MSRP: $4.72
You Save: $1.72 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Inter Shf Hsg
Part Number: 84513479
$16.92 MSRP: $30.76
You Save: $13.84 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Front Whl Drv Inter Shf Hsg
Part Number: 24295329
$16.03 MSRP: $26.52
You Save: $10.49 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal, Rear Whl Hub (O Ring)
Part Number: 84273180
$4.69 MSRP: $8.42
You Save: $3.73 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly Seal, Rear Hub Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal Assembly, R/Axl Shf
Part Number: 84649193
$8.20 MSRP: $14.70
You Save: $6.50 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal Assembly, R/Axl Shf
Part Number: 84649194
$8.20 MSRP: $14.70
You Save: $6.50 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Seal
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Tahoe | 4 DOOR 1/2 TON | 8 Cyl 5.3L, 8 Cyl 6.2L
View related parts
Chevrolet Tahoe Seal,Front Wheel Inner Bearing
Part Number: 15589666
Product Specifications
- Other Name: SEAL, Front Wheel Bearing; Grease Seal, Inner Seal, Seal, Wheel Seal
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1998 Chevrolet Tahoe | CLASSIC 4 DOOR 1/2 TON
View related parts
Chevrolet Tahoe Seal,Front Wheel Inner Bearing
Part Number: 15521904
Product Specifications
- Other Name: SEAL, Front Wheel Bearing
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L, 8 Cyl 6.5L Diesel
View related parts
Chevrolet Tahoe Seal,Front Drive Axle Inner Shaft
Part Number: 26031569
Product Specifications
- Other Name: SEAL, Front Axle; Output Shaft Seal
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Tahoe | CLASSIC 2 DOOR 1/2 TON, CLASSIC 4 DOOR 1/2 TON | 8 Cyl 5.7L, 8 Cyl 6.5L Diesel

| Page 1 of 2 |Next >

1-20 of 21 Results

Chevrolet Tahoe Wheel Seal Parts Questions & Experts Answers

Seal,Rear Axle Shaft
12471686
Q: How to remove and install a rear hub assembly,Wheel Bearing and Wheel Seal for Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: To remove and install a rear hub assembly, first remove the axleshaft and rear wheels, then remove the brake disc and retaining ring/key from the end of the axle housing. Use a special socket to remove the adjusting nut and pull the hub assembly straight off the axle tube. Discard the oil seal and clean and inspect all components for wear or damage. Disassemble the hub further if necessary, then clean and reassemble using new bearing cups and lubricating with wheel bearing grease. To install, place the hub assembly on the axle tube and adjust the bearings by tightening the adjusting nut to 50 ft-lbs, then backing it off and tightening it hand-tight. Install the key and retaining ring, and ensure there is no play in the hub assembly before reinstalling the axleshaft and lowering the vehicle.
Seal Assembly, Front Drive Axle Inner Shaft
22761722
Q: How to replace and install the front Wheel Bearing and Wheel Seal of 4WD Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: To remove the left side of a vehicle, first loosen the wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the left front wheel. Then, remove the differential carrier splash shield from under the front axle and the left driveaxle. Drain the lubricant from the front differential and pull the left Axle Shaft out with a slide hammer and adapter. Remove the deflector and seal from the differential and remove the bearing using a slide hammer and bearing remover attachment. To install the left side, first install the bearing with the square shoulder facing in, using a bearing driver or a socket with an outside diameter slightly smaller than that of the bearing. Then, install a new seal and deflector, lubricating the lips of the seal with multi-purpose grease. Carefully drive in the axle shaft with a soft-face hammer and fill the differential with the proper lubricant. Install the driveaxle and differential carrier splash shield, then install the wheel and lug nuts. Lower the vehicle, tighten the lug nuts to the proper torque specifications, and check for proper operation.
Seal,Rear Axle Shaft
12471686
Q: How to replace rear oil seal from the end of an axle housing on Chevrolet Avalanche,Silverado,Suburban,Tahoe,GMC Sierra,Yukon,Yukon Denali and Yukon XL?
A: To remove the oil seal from the end of the axle housing, remove the Axle Shaft. Then, use a pry tool to remove the oil seal. Apply a film of multi-purpose grease to the oil seal recess and install the new seal evenly with a hammer and seal installation tool. The oil seal should be aligned with the axle housing. Finally, install the axle shaft.