GMC 23104840 Joint Kit, Front Axle Propeller Shaft Front Universal

You can Select Your Vehicle to check if 23104840 fits your vehicle.

Wear in needle roller bearings can be identified by various symptoms such as vibration in the transmission, clonks during drive engagement, metallic squeaking, and eventually grating and shrieking sounds as the bearings deteriorate. To check for wear, one can try turning the shaft with one hand while holding the rear axle flange or front half coupling with the other hand to detect any movement between the shaft and the couplings. Another test involves attempting to lift the shaft and observing any movement between the yokes of the joints. If significant wear is observed, it is recommended to either replace the universal joints or opt for a new driveshaft assembly.

To perform a Cleveland type joint repair, start by cleaning the ends of the bearings on the yokes and removing the snap-rings using snap-ring pliers. If the snap-rings are tight, tap the bearing cup to relieve pressure. Support the trunnion yoke and press out the trunnion using a vise and a socket. Grip the bearing cup in a vise to fully remove it, and repeat for the remaining cups. Ensure the vent hole on the slip yoke is not blocked. Use a universal joint repair kit to replace the trunnion, seals, bearings, cups, and snap-rings. Begin reassembly by packing lubricant into the trunnion ends. Place the dust seals correctly on the trunnion and insert one bearing cup into the yoke, followed by needle rollers. Insert the trunnion into the cup and stick needle bearings into the opposite cup. Press both cups fully home in the vise and install new snap-rings. Repeat for the other bearing cups. If the bearing cup housings are excessively worn, replace the entire driveshaft assembly. Always check the wear in the sliding sleeve splines and replace if necessary. For a Saginaw type joint, follow a similar procedure, removing snap-rings if necessary and removing plastic material from the yoke after removing the trunnion. Reassembly is the same, with snap-rings installed inside the yoke. If needed, strike the yoke with a hammer to assist in seating.

A driveshaft is a tube or pair of tubes that transmits power between the transmission and differential, with universal joints located at either end and in the center of two-piece driveshafts. Single piece driveshafts have a splined yoke at the front that allows for movement during vehicle operation, while two-piece driveshafts have a slip joint on the front of the rear section and a center support bearing. The driveshaft assembly requires little service, with universal joints lubricated for life and replaced if problems arise. Inspection involves checking for dents, cracks, and oil leakage, as well as ensuring proper operation of universal joints and center bearings. Driveshaft mounting bolts should also be checked for tightness, and similar checks should be performed on the front driveshaft and driveaxles of 4WD models. Noise or vibration while driving may indicate problems with the driveshaft or other components.

To remove a universal joint, it will vary depending on whether it is an outer snap-ring type or an injected plastic type. The snap rings are then removed with pliers, and force out the bearing caps. The U-joint is then removed and replaced with a new one and the bearing cap bores are inspected. For the injected plastic type, the snap-rings are removed if the joint has been rebuilt. Reassembly is the same as for the outer snap-ring joint, except the snap-rings are on the inner part of each bearing cap. If the joint is stiff after assembly, the yoke ears can be struck with a hammer to free up the joint.

The two types of universal joints mentioned are the outer snap-ring type and the injected plastic (inner snap-ring) type.

Single piece driveshafts have a splined yoke at the front that allows for movement during vehicle operation, while two-piece driveshafts have a slip joint on the front of the rear section and a center support bearing.

In 4WD models, the driveshaft may have a splined yoke or companion flange at the transfer case end, and two-piece driveshafts usually have a slip joint at the front of the rear section.

Inspect the bearing cup housing for wear and damage. If necessary, replace the driveshaft. Make sure the dust seals are properly located on the trunnion.

For the injected plastic (inner snap-ring) type, if the joint has been previously rebuilt, remove the snap-rings located on the inner part of each bearing cup. For first-time rebuilding, it won't be necessary to remove the snap-rings; the pressing operation will shear the molded plastic retaining material.

Two-piece driveshafts usually have a slip joint at the front of the rear section, which allows for movement and flexibility.

Reassembly is similar to the outer snap-ring joint, but the snap-rings are on the inner part of each bearing cup. When installing the bearing cup, press it in until the snap-ring can be installed, and if needed, strike the yoke with a hammer to allow the snap-ring groove to move into position.

Inspect the bearing cup housing for wear and damage. If necessary, replace the driveshaft. Make sure the dust seals are properly located on the trunnion.

Problems with the driveshaft are usually indicated by noise or vibration while driving, and a road test can help determine if the driveshaft is the issue.

Inspect the bearing cup housing for wear and damage. If necessary, replace the driveshaft. Make sure the dust seals are properly located on the trunnion.

In 2WD models, the driveshaft has a splined yoke at the front that allows it to slide back and forth within the transmission, with an oil seal to prevent fluid leakage and dirt entry.

The two types of universal joints mentioned are the outer snap-ring type and the injected plastic (inner snap-ring) type.

In 4WD models, the driveshaft may have a splined yoke or companion flange at the transfer case end, and two-piece driveshafts usually have a slip joint at the front of the rear section.

A driveshaft is a tube or pair of tubes that transmits power between the transmission and differential.

Driveshaft mounting bolts should be checked for tightness.

In 4WD models, the front driveshaft and driveaxles should also be checked.

The process for replacing the injected plastic type universal joint involves removing the snap-rings if the joint has been previously rebuilt, and pressing out the bearing caps. The U-joint is then removed and cleaned, and the plastic material is removed from the yoke. Reassembly is the same as for the outer snap-ring joint, except the snap-rings are on the inner part of each bearing cap. If the joint is stiff after assembly, the yoke ears can be struck with a hammer to free up the joint.

Remove the snap-rings on the inner part of each bearing cup. Press out the bearing cups and remove the trunnion. Clean all plastic material from the yoke.

The driveshaft requires minimal service, with the universal joints being lubricated for life and replaced if problems arise.

Noise or vibration while driving may indicate problems with the driveshaft or other components.