Make sure this part fits

GM 15684319 Steering Knuckle

1991-1997 GM

Customer Questions & Expert Answers (9)
GM 15684319 Steering Knuckle
  • Part Description
    Knuckle,Steering
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number15684319
    Part DescriptionKnuckle,Steering
    Other NamesKnuckle
    Item Dimensions14.8 x 10.6 x 7.0 inches
    Item Weight11.70 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU15684319
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    1995-1996 Chevrolet Blazer6 Cyl 4.3L2 DOOR, 4 DOOR
    1991-1997 Chevrolet S104 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L2 DOOR, 4 DOOR, ELECTRIC, PICKUP
    1992-1996 GMC Jimmy6 Cyl 4.3L2 DOOR, 4 DOOR
    1991 GMC S156 Cyl 4.3L2 DOOR, 4 DOOR
    1991-1996 GMC Sonoma4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3LPICKUP
    1991 GMC Syclone6 Cyl 4.3LPICKUP
    1992-1993 GMC Typhoon6 Cyl 4.3L2 DOOR, 4 DOOR
    1996, 1991-1994 Oldsmobile Bravada6 Cyl 4.3LBRAVADA
  • Customer Questions & Expert Answers

    Q:
    I am wonder if this is complete and correct part for my vehicle. Posted by GMPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 15684319 fits your vehicle.
    Posted by GMPartsGiant Specialist
    Q:
    How do you remove the Steering Knuckle of 4WD Chevrolet Blazer,S10,GMC Jimmy and Sonoma? Posted by Customer
    A:
    To remove the drive axle/hub, put the vehicle in gear, apply the parking brake, and break loose the drive axle/hub nut with a socket. Use a puller to push the drive axle out while withdrawing the steering knuckle and hub assembly. To install the drive axle/hub, simply reverse the removal procedure, and lubricate the drive axle splines with multi-purpose grease.
    Posted by GMPartsGiant Specialist
    Q:
    What should you do after supporting the lower control arm with a floor jack for the 1998 Chevrolet Blazer? Posted by Customer
    A:
    Detach the steering knuckle from the lower ball joint and support the steering knuckle while separating it from the upper ball joint.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    What is the final step in removing the front suspension for the 1996 Chevrolet Blazer? Posted by Customer
    A:
    Finally, remove the steering knuckle.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    How do you install the front suspension for the 2002 Chevrolet S10? Posted by Customer
    A:
    To install the front suspension, simply reverse the removal steps. Make sure to adjust the front wheel bearings and have the front wheel alignment checked afterwards.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    What should you inspect and potentially replace during the process for the 1996 Chevrolet S10? Posted by Customer
    A:
    Inspect the seal on the rear side of the knuckle and replace it if necessary by driving in a new seal with a socket that has a slightly smaller outside diameter.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    What should you do next after raising the 2000 GMC Jimmy and supporting it securely on jack stands? Posted by Customer
    A:
    Support the lower control arm with a jack to compress the coil spring to its normal ride height.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    What steps should be taken after securing the 2001 GMC Jimmy on jackstands? Posted by Customer
    A:
    Remove the wheel and the driveaxle/hub nut.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    Q:
    What should you do after removing the brake caliper, brake disc/hub assembly, and disc splash shield of the 1998 GMC Sonoma? Posted by Customer
    A:
    Disconnect the tie-rod end from the knuckle and disconnect the ball joints from the steering knuckle.
    Posted by GMPartsGiant Specialist
    See expert answers on similar Steering Knuckle
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine GM Part 15684319, the Right Choice

Your vehicle deserves only genuine OEM GM parts and accessories. To ensure reliability, purchase GM part # 15684319 Steering Knuckle. It is sometimes referred to as GM Steering Knuckle. Our GM parts and accessories are expedited directly from authorized GM dealers strategically located all across the U.S. and are backed by the manufacturer's 12 month, 12,000 mile warranty. OEM GM parts are the best for restoring your vehicle to factory condition performance. This part fits specific Chevrolet Blazer, S10 models. It fits GMC Jimmy, S15, Sonoma. It also fits Oldsmobile Bravada.

Affordable, reliable and built to last, GM part # 15684319 Steering Knuckle stands out as the smart option. GMPartsGiant.com is your prime online source with the biggest and best selection of genuine GM parts and accessories at giant discounted prices. We have the OEM GM parts and accessories you need at the wholesale prices. GMPartsGiant.com has you covered no matter what type of GM vehicle you drive. For detailed GMC parts information, click here.

Why choose GM Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly