How do you remove the Steering Knuckle of 4WD Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the drive axle/hub, put the vehicle in gear, apply the parking brake, and break loose the drive axle/hub nut with a socket. Use a puller to push the drive axle out while withdrawing the steering knuckle and hub assembly. To install the drive axle/hub, simply reverse the removal procedure, and lubricate the drive axle splines with multi-purpose grease.

How do you remove the Steering Knuckle of 2WD Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the front suspension of a vehicle, start by raising the front of the vehicle and supporting it securely on jack stands. Apply the parking brake for safety. Then, support the lower control arm with a jack to compress the coil spring to its normal ride height. Remove the wheel and disconnect the ABS wheel speed sensor. Next, remove the brake caliper and the brake disc/hub assembly. If equipped, remove the disc splash shield. Disconnect the tie-rod end from the knuckle and disconnect the ball joints from the steering knuckle. Finally, remove the steering knuckle. To install the front suspension, simply reverse the removal steps. Make sure to adjust the front wheel bearings and have the front wheel alignment checked afterwards.

Genuine GMC Sonoma Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Steering Knuckles found

View related parts
GMC Sonoma Steering Knuckle
Part Number: 15684320
Product Specifications
- Other Name: Knuckle,Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Steering Knuckle
Part Number: 15684319
Product Specifications
- Other Name: Knuckle,Steering; Knuckle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Steering Knuckle Assembly
Part Number: 18060564
Product Specifications
- Other Name: Knuckle Asm,Steering ; Knuckle, Steering; Knuckle, Steering Knuckle
- Replaces: 15958716
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2003 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Knuckle Steering
Part Number: 19303837
Product Specifications
- Other Name: Knuckle,Steering ; Knuckle,Strg
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Knuckle Steering
Part Number: 19303838
Product Specifications
- Other Name: Knuckle,Steering
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L

GMC Sonoma Steering Knuckle

Steering Steering Knuckle of GMC Sonoma automobiles is an important linkage that lies in between the suspension and the steering apparatuses of the car to the wheels. They give supporting anchors for the control arms, the tie-rod ends and spindles or hubs respectively. The knuckle lets the wheels travel up and down because of the surface irregularities and can horizontally owing to the direction of the vehicle. Depending on the type of the car, there are several types of steering knuckles including the types rear-wheel drive, front and all-wheel or four-wheel drive with the difference in the spindle and hub combination. Steering knuckles have evolved from the kingpin to complex constructions and are long lasting with wear and tear components that do not need replacement often except when they are damaged. Daily or regular inspection of the knuckle stud bores, spindles and bushing is advised to company better performance and safety.

Each OEM GMC Sonoma Steering Knuckle we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Sonoma Steering Knuckle Parts Questions & Experts Answers

Steering Knuckle
15684319
Q: How do you remove the Steering Knuckle of 4WD Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the drive axle/hub, put the vehicle in gear, apply the parking brake, and break loose the drive axle/hub nut with a socket. Use a puller to push the drive axle out while withdrawing the steering knuckle and hub assembly. To install the drive axle/hub, simply reverse the removal procedure, and lubricate the drive axle splines with multi-purpose grease.
Steering Knuckle
15684320
Q: How do you remove the Steering Knuckle of 2WD Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the front suspension of a vehicle, start by raising the front of the vehicle and supporting it securely on jack stands. Apply the parking brake for safety. Then, support the lower Control Arm with a jack to compress the coil spring to its normal ride height. Remove the wheel and disconnect the ABS wheel speed sensor. Next, remove the brake caliper and the brake disc/hub assembly. If equipped, remove the disc splash shield. Disconnect the tie-rod end from the knuckle and disconnect the Ball Joints from the steering knuckle. Finally, remove the steering knuckle. To install the front suspension, simply reverse the removal steps. Make sure to adjust the front wheel bearings and have the front wheel alignment checked afterwards.