GM 25997509 Front Lower Control Arm Assembly

You can Select Your Vehicle to check if 25997509 fits your vehicle.

To remove and install a lower control arm on a vehicle, first loosen the wheel lug nuts, raise the vehicle, and support it securely on jackstands placed under the frame rails. Disconnect the stabilizer bar link from the control arm and remove the shock absorber lower mounting fasteners. On 4WD models, remove the front driveaxle. If working on a model with torsion bar front suspension, remove the torsion bar. Using rope or wire, support the upper control arm and steering knuckle from the top of the shock absorber. To disconnect the lower control arm from the steering knuckle, loosen the ball joint nut a few turns, install a ball joint separator and break the ball joint loose from the knuckle, then remove the nut. Remove the lower control arm pivot bolts and nuts, noting which way the bolts are installed and, on 4WD models, how the washers are installed. Pull the lower arm from its frame brackets. To install the arm, position it in the frame brackets and install the bolts and nuts, but don't tighten them yet. Attach the balljoint to the steering knuckle, install a new nut, and tighten it to the torque specifications. The remainder of installation is the reverse of removal. Be sure to tighten all fasteners to the torque specifications. Install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts to the torque specifications. If working on a model with torsion bar front suspension, be sure to check and adjust the ride height. Have the front-end alignment checked and, if necessary, adjusted.

The initial steps to remove the upper control arm on a vehicle are as follows: Loosen the wheel lug nuts. Raise the front of the vehicle. Support the vehicle securely on jack stands. Remove the wheel.

To install the new lower control arm, follow these steps: Position the arm in the frame brackets and install the bolts and nuts, but don't tighten them yet. Attach the ball joint to the steering knuckle. Install a new nut on the ball joint and tighten it to the torque specifications.

The initial steps to remove the upper control arm on a vehicle are as follows:Loosen the wheel lug nuts. Raise the front of the vehicle. Support the vehicle securely on jack stands. Remove the wheel.

To disconnect the lower control arm from the steering knuckle, follow these steps: Loosen the ball joint nut a few turns. Install a ball joint separator and break the ball joint loose from the knuckle. Remove the nut.

To install the new upper control arm, follow these steps:Position the arm in the frame brackets and install the bolts and nuts, but don't tighten them yet.Attach the ball joint to the steering knuckle.Install a new nut on the ball joint and tighten it to the torque specifications.

After disconnecting the ball joint, proceed with these steps:Remove the lower control arm pivot bolts and nuts, noting the orientation of the bolts and, on 4WD models, how the washers are installed. Pull the lower arm from its frame brackets.

The initial steps to remove the upper control arm on a vehicle are as follows: Loosen the wheel lug nuts. Raise the front of the vehicle. Support the vehicle securely on jack stands. Remove the wheel.

To finalize the installation of the lower control arm, follow these steps: Complete the remainder of the installation in reverse order of removal. Be sure to tighten all fasteners to the torque specifications. Install the wheel and lug nuts. Lower the vehicle and tighten the lug nuts to the torque specifications. If working on a model with torsion bar front suspension, check and adjust the ride height. Have the front-end alignment checked and, if necessary, adjusted.

Before removing the lower control arm, you should do the following: Disconnect the stabilizer bar link from the control arm. Remove the shock absorber lower mounting fasteners. If it's a 4WD model, remove the front driveaxle. If working on a model with torsion bar front suspension, remove the torsion bar. Use rope or wire to support the upper control arm and steering knuckle from the top of the shock absorber.

To finalize the installation of the upper control arm, follow these steps: Ensure that the marks made prior to disassembly are aligned. Tighten the nuts on the control arm to the torque specifications. Tighten the wheel lug nuts to the torque specifications. Have the front-end alignment checked and, if necessary, adjusted.

The initial steps to remove the upper control arm on a vehicle are as follows: Loosen the wheel lug nuts. Raise the front of the vehicle. Support the vehicle securely on jack stands. Remove the wheel.

they were replaced with steel. Aluminum no longer available