Chevrolet 12637710 Seal Assembly, Crankshaft Rear Oil

You can Select Your Vehicle to check if 12637710 fits your vehicle.

At the time of publication, the rear crankshaft seal is supplied as an assembly consisting of the oil seal and housing. The manufacturer recommends using special studs EN 46109, seal alignment tool EN 47839 and handle J 42183 to ensure correct alignment of the seal. These tools are available through SPX Tools. Disconnect the cable from the negative battery terminal. Remove the driveplate. Remove the oil pan. Remove the retaining bolts, then remove and discard seal housing from the engine (Rear crankshaft seal housing bolts). It may be necessary to use a knife to cut the sealant away from the joint between the rear crankshaft seal housing and the engine block. There are specific points provided at the corners for prying the seal housing. Use care not to scratch the machined faces of the cylinder block, rear crankshaft seal housing or oil pan when scraping old gasket material from components. Thoroughly clean the mounting surfaces of the oil pan, rear crankshaft seal housing and engine block of old gasket material and sealer. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Install the two dowels into the oil seal housing bolt holes (Alignment dowels installed in the rear crankshaft seal housing bolt holes). Apply a 1/8-inch wide bead of RTV sealant around the sealing area of the oil seal housing, passing on the inside of the bolt holes. Install the special alignment tool (EN47839) on the rear of the crankshaft, attaching it with the two supplied screws. Install the new oil seal housing over the alignment tool and studs onto the rear of the engine block. Remove the guide studs but leave the alignment tool in place. Install the housing bolts and tighten them to the torque. Remove the alignment tool. The remainder of installation is the reverse of removal. Add oil as necessary, run the engine and check for leaks.

At the time of publication, the rear crankshaft seal is supplied as an assembly consisting of the oil seal and housing. The manufacturer recommends using special studs EN 46109, seal alignment tool EN 47839 and handle J 42183 to ensure correct alignment of the seal. These tools are available through SPX Tools. Disconnect the cable from the negative battery terminal. Remove the driveplate. Remove the oil pan. Remove the retaining bolts, then remove and discard seal housing from the engine (Rear crankshaft seal housing bolts). It may be necessary to use a knife to cut the sealant away from the joint between the rear crankshaft seal housing and the engine block. There are specific points provided at the corners for prying the seal housing. Use care not to scratch the machined faces of the cylinder block, rear crankshaft seal housing or oil pan when scraping old gasket material from components. Thoroughly clean the mounting surfaces of the oil pan, rear crankshaft seal housing and engine block of old gasket material and sealer. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Install the two dowels into the oil seal housing bolt holes (Alignment dowels installed in the rear crankshaft seal housing bolt holes). Apply a 1/8-inch wide bead of RTV sealant around the sealing area of the oil seal housing, passing on the inside of the bolt holes. Install the special alignment tool (EN47839) on the rear of the crankshaft, attaching it with the two supplied screws. Install the new oil seal housing over the alignment tool and studs onto the rear of the engine block. Remove the guide studs but leave the alignment tool in place. Install the housing bolts and tighten them to the torque. Remove the alignment tool. The remainder of installation is the reverse of removal. Add oil as necessary, run the engine and check for leaks.

At the time of publication, the rear crankshaft seal is supplied as an assembly consisting of the oil seal and housing. The manufacturer recommends using special studs EN 46109, seal alignment tool EN 47839 and handle J 42183 to ensure correct alignment of the seal. These tools are available through SPX Tools. Disconnect the cable from the negative battery terminal. Remove the driveplate. Remove the oil pan. Remove the retaining bolts, then remove and discard seal housing from the engine (Rear crankshaft seal housing bolts). It may be necessary to use a knife to cut the sealant away from the joint between the rear crankshaft seal housing and the engine block. There are specific points provided at the corners for prying the seal housing. Use care not to scratch the machined faces of the cylinder block, rear crankshaft seal housing or oil pan when scraping old gasket material from components. Thoroughly clean the mounting surfaces of the oil pan, rear crankshaft seal housing and engine block of old gasket material and sealer. Wipe the gasket surfaces clean with a rag soaked in brake system cleaner. Install the two dowels into the oil seal housing bolt holes (Alignment dowels installed in the rear crankshaft seal housing bolt holes). Apply a 1/8-inch wide bead of RTV sealant around the sealing area of the oil seal housing, passing on the inside of the bolt holes. Install the special alignment tool (EN47839) on the rear of the crankshaft, attaching it with the two supplied screws. Install the new oil seal housing over the alignment tool and studs onto the rear of the engine block. Remove the guide studs but leave the alignment tool in place. Install the housing bolts and tighten them to the torque. Remove the alignment tool. The remainder of installation is the reverse of removal. Add oil as necessary, run the engine and check for leaks.

Remove the crankshaft pulley. Note how the seal is installed-the new one must be installed to the same depth and facing the same way. Carefully pry the seal out of the cover. If you don't have a seal removal tool, thread a self tapping screw partially into the seal, then use pliers as a lever to pull it from the engine. If the seal is being replaced with the timing chain cover removed, support the cover on top of two blocks of wood and drive the seal out from the rear with a hammer and punch. Caution: Be careful not to scratch, gouge or distort the area that the seal fits into or a leak will develop. Installation: Apply clean engine oil or multi-purpose grease to the outer edge of the new seal, then install it in the cover with the lip (spring side) facing IN. Drive the seal into place with a seal driver or a large socket and a hammer. Make sure the seal enters the bore squarely and stop when the front face is at the proper depth. Note: Don't let oil get on the rubber part of the seal or on the part of the crankshaft pulley that touches the seal. The seal must be installed dry. Check the surface on the pulley hub that the seal rides on. If the surface has been grooved from long-time contact with the seal, the pulley should be replaced with a new one. Lubricate only the inside of the pulley hub with clean engine oil and install the crankshaft pulley. The remainder of installation is the reverse of removal.

Be careful not to scratch, gouge, or distort the area that the seal fits into, as it may cause a leak.

It is important for ensuring the proper installation depth of the new seal.

Thoroughly clean the mounting surfaces of the oil pan, rear main oil seal housing, and engine block of old gasket material and sealer, using a rag soaked in lacquer thinner, acetone, or brake cleaner.

Apply clean engine oil or multi-purpose grease to the outer edge of the new seal.

The lip of the new seal, which contacts the crankshaft, should be coated with clean engine oil before installation.

Install the new seal in the cover with the lip facing inward, using a large socket and hammer to drive it into place, ensuring it enters the bore squarely and stops at the proper depth.

Begin by removing the transmission and the flywheel/driveplate.

Be very careful not to distort the cover or scratch the crankshaft, and wrap electrical tape around the tip of the screwdriver to avoid damage.

Drive the seal into place with a large socket and a hammer, or a piece of pipe if a large socket isn't available, ensuring the seal enters the bore squarely.

The lip should point toward the engine.

Proceed to install the oil pan and flywheel/driveplate.

The first step is to disconnect the cable from the negative battery terminal and remove the drivebelt.

The manufacturer recommends using special studs EN 46109, seal alignment tool EN 47839, and handle J 42183 to ensure correct alignment of the seal.

Position the new seal onto the crankshaft, ensuring the edges are not rolled over.

Obtain a special installation tool EN-48108, which is necessary for properly installing the new seal.

Check the pulley hub surface for grooves caused by long-term contact with the seal; if damaged, replace the pulley.

Complete the installation by reversing the removal steps.

Don't let oil get on the rubber part of the seal or on the part of the crankshaft pulley that touches the seal. The seal must be installed dry.

Install a new center bolt and tighten it to the specified torque, ensuring a new pulley bolt is used.

Complete the installation by reversing the removal steps.

Thoroughly clean the mounting surfaces of the oil pan, rear main oil seal housing, and engine block of old gasket material and sealer, wiping the gasket surfaces with a rag soaked in brake system cleaner.

Install the new seal in the cover with the lip facing inward, driving it into place with a seal driver or a large socket and hammer, ensuring it enters squarely and is at the correct depth.

Install the new seal in the cover with the lip facing inward, then drive the seal into place with a large socket and a hammer, or a piece of pipe if a large socket isn't available, ensuring the seal enters the bore squarely and stops at the proper depth.

Begin by disconnecting the cable from the negative battery terminal.

Inspect the oil seal, oil pan, and engine block surface for signs of leakage, as an oil pan gasket leak can sometimes mimic a rear oil seal leak.

Remove the tool and check the position of the new seal.

If marked, ensure that the words "THIS SIDE OUT" on the seal face out, toward the rear of the engine.

The first step is to disconnect the cable from the negative terminal of the battery and remove the drivebelt.

Lubricate the pulley hub with clean engine oil.

It is important to be very careful not to scratch or damage the crankshaft sealing surface or the bore in the engine block.