How to remove and install an oil pan in V8 engine on Oldsmobile Cutlass?

Having instilled the engine into a vehicle, follow the procedures of How to Start, by removing the negative BAT cable and air cleaner assembly. Then, remove the distributor cap in order to avoid damaging it when lifting the engine and then unbolt the radiator shroud from the radiator support and hook it on the cooling fan. Lift the vehicle and place it on jack stands; further, dismantle the oil dipstick and dipstick tube. Siphon the engine oil and flush the engine and then remove the exhaust crossover pipe at the exhaust manifold flanges and drop the exhaust pipes and hold them with wire on the frame. In the case that the vehicle has automatic transmission, then the first parts to be taken off include the converter underpan, starter and the flywheel cover. Turn the engine counterclockwise with a bolt at the middle of the torsional damper so that the favourite timing mark points to the number 1 cylinder which means that the engine is now at top dead centre, although this will give some clearance at the front of the oil pan. Loosen and take out the through bolt of every engine mount followed by lifting the engine with the aid of an engine hoist or cherry picker to enable you to slide the oil pan away from the cross-member. Another procedure rely on the use of a floor jack with a piece of wood placed underneath the oil pan to avoid any scratching. Lift the engine further until wood blocks can be wedged in between the frame front crossmember and the engine block; reference should be made to clearance round the engine, especially with distributor and cooling fan. Place the engine on the wooden blocks such that it is well balanced and then remove the oil pan bolts, and if necessary the heads as well, considering the sizes and positions. Lower the rear of the oil pan down and wiggle the front free of the crossmember; use a rubber mallet if you need to apply serious amounts of force. Before installation the gasket sealing surfaces must be free from sealer and gasket materials, clean them properly. Place the new side gaskets to the engine block, be sure that the bolt holes align then spread a thin layer of sealer on the gaskets. Set the front and rear seals into the sealer and jam the ends of these to the side gaskets ends. Place the pan in the required position and fit all bolts loosely up to the position when they can be tightened using fingers, and then tighten the end bolts. Lower the engine onto its mounts and install the through bolts tightening them to the standard torque. Work in reverse, adding the proper grade and amount of oil, turn on the engine, and you are required to check if there is any leakage. If the engine has been pulled out from the vehicle, then most of the steps pertaining to above will not come into the picture and the pan will simply bolted and can be lifted off from the engine block in the process discussed earlier, while the installation process will involve cleaning and sealing steps described above.

Genuine Oldsmobile Cutlass Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Oil Pans found

View related parts
Oldsmobile Cutlass Pan Kit,Automatic Transmission Oil (M6) *Includes Pan,Ma
Part Number: 24211988
$56.16 MSRP: $154.10
You Save: $97.94 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN KIT, Automatic Transmission Fluid; Transmission Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Pan Asm,Oil
Part Number: 12512670
$174.96 MSRP: $276.52
You Save: $101.56 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, SC 2 DOOR, SEDAN LEVEL I, SEDAN LEVEL II, SL 4 DOOR | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Pan Asm,Oil
Part Number: 24504719
$48.11 MSRP: $136.14
You Save: $88.03 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1994 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, INTERNAL 2 DOOR, INTERNAL 4 DOOR | 6 Cyl 2.8L, 6 Cyl 3.1L, 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 12577511
$177.94 MSRP: $235.61
You Save: $57.67 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 10223711
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, INTERNAL 2 DOOR, INTERNAL 4 DOOR, S 4 DOOR, S STATION WAGON, SL 4 DOOR, SL STATION WAGON | 6 Cyl 3.1L
View related parts
Oldsmobile Cutlass Pan, Automatic Transmission Oil
Part Number: 8643574
Product Specifications
- Other Name: PAN, Transmission Oil Pan; Transmission Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1996 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, INTERNAL 2 DOOR, INTERNAL 4 DOOR, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, S 4 DOOR, S STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 4 Cyl 2.2L, 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.1L, 6 Cyl 3.3L, 6 Cyl 3.4L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 24503557
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 6 Cyl 3.4L
View related parts
Oldsmobile Cutlass Pan,Automatic Transmission Oil (Remanufacture)
Part Number: 24202236
Product Specifications
- Other Name: PAN, Transmission Oil
- Replaces: 08648349, 8648349
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR, CUTLASS CALAIS, CUTLASS CRUISER | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Pan,Automatic Transmission Oil
Part Number: 8657035
Product Specifications
- Other Name: PAN, Transmission Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR, CUTLASS CALAIS, CUTLASS CRUISER | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L, 8 Cyl 5.0L, 8 Cyl 5.7L Diesel
View related parts
Oldsmobile Cutlass Pan Kit, W/Gasket & Bolts, Trans Oil
Part Number: 8653942
Product Specifications
- Other Name: PAN, Transmission Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1988 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.3L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 3.0L, 6 Cyl 3.8L, 6 Cyl 4.3L Diesel, 8 Cyl 4.3L
View related parts
Oldsmobile Cutlass Pan,Oil
Part Number: 25522384
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR, LS 2 DOOR, LS 4 DOOR, LS STATION WAGON | 6 Cyl 3.0L, 6 Cyl 3.8L
View related parts
Oldsmobile Cutlass Pan Kit,Oil(W/Gasket)
Part Number: 12353406
Product Specifications
- Other Name: PAN; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, S 4 DOOR, S STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 6 Cyl 3.3L
View related parts
Oldsmobile Cutlass Pan,Oil
Part Number: 88890999
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12513704, 12363172
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Oldsmobile Cutlass | S 4 DOOR, S STATION WAGON, SL 4 DOOR, SL STATION WAGON | 4 Cyl 2.2L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 10044683
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, LS 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR, STATION WAGON | 4 Cyl 2.5L
View related parts
Oldsmobile Cutlass Pan,Oil
Part Number: 14077873
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR NOTCHBACK, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, LS 2 DOOR NOTCHBACK, LS 4 DOOR, LS STATION WAGON, S 2 DOOR | 6 Cyl 2.8L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 10101752
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1992 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, S 2 DOOR, S 4 DOOR, S STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 4 Cyl 2.5L
View related parts
Oldsmobile Cutlass Pan,Oil
Part Number: 25522386
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Replaces: 12360301
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR, CUTLASS CALAIS, CUTLASS CRUISER | 6 Cyl 3.8L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 555137
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1987 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 2 DOOR, BROUGHAM 4 DOOR, CUTLASS CALAIS, CUTLASS CRUISER | 8 Cyl 4.3L, 8 Cyl 5.0L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 10044674
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 Oldsmobile Cutlass | 2 DOOR, 4 DOOR, BROUGHAM 4 DOOR, BROUGHAM SL 2 DOOR, BROUGHAM STATION WAGON, SL 2 DOOR, SL 4 DOOR, SL STATION WAGON, STATION WAGON | 4 Cyl 2.5L
View related parts
Oldsmobile Cutlass Pan Assembly, Oil
Part Number: 22538921
Product Specifications
- Other Name: PAN, Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Oldsmobile Cutlass | 2 DOOR, 4 DOOR | 4 Cyl 2.3L, 6 Cyl 3.1L

Oldsmobile Cutlass Oil Pan

The Oil Pan used in Oldsmobile Cutlass vehicles is used to hold the engine oil and distribute the load needed to reduce friction of parts in motion. A wet sump system of Oil Pan is used, the oil is drawn through a pickup tube by the oil pump and circulates the oil in the engine. This design helps Oldsmobile Cutlass to have a proper lubrication and proper flow of coolants for the engine parts. Traditionally, Oldsmobile Cutlass models used stamped steel for the oil pans but with the new developments, cast aluminum is used in current models. All these variations of the material owe their existence to an enhancement of the device's performance and productivity. The Oil Pan also takes into consideration adequate supply of the oil in different operating conditions as this will enhance the performance of the Oldsmobile Cutlass in its lubrication system.

Each OEM Oldsmobile Cutlass Oil Pan we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Oldsmobile Cutlass Oil Pan Parts Questions & Experts Answers

Pan Asm,Oil
12512670
Q: How to remove and install an oil pan in V8 engine on Oldsmobile Cutlass?
A: Having instilled the engine into a vehicle, follow the procedures of How to Start, by removing the negative BAT cable and air cleaner assembly. Then, remove the distributor cap in order to avoid damaging it when lifting the engine and then unbolt the radiator shroud from the radiator support and hook it on the cooling fan. Lift the vehicle and place it on jack stands; further, dismantle the oil dipstick and dipstick tube. Siphon the engine oil and flush the engine and then remove the exhaust crossover pipe at the exhaust manifold flanges and drop the exhaust pipes and hold them with wire on the frame. In the case that the vehicle has automatic transmission, then the first parts to be taken off include the converter underpan, starter and the flywheel cover. Turn the engine counterclockwise with a bolt at the middle of the torsional damper so that the favourite timing mark points to the number 1 cylinder which means that the engine is now at top dead centre, although this will give some clearance at the front of the oil pan. Loosen and take out the through bolt of every engine mount followed by lifting the engine with the aid of an engine hoist or cherry picker to enable you to slide the oil pan away from the cross-member. Another procedure rely on the use of a floor jack with a piece of wood placed underneath the oil pan to avoid any scratching. Lift the engine further until wood blocks can be wedged in between the frame front crossmember and the engine block; reference should be made to clearance round the engine, especially with distributor and cooling fan. Place the engine on the wooden blocks such that it is well balanced and then remove the oil pan bolts, and if necessary the heads as well, considering the sizes and positions. Lower the rear of the oil pan down and wiggle the front free of the crossmember; use a rubber mallet if you need to apply serious amounts of force. Before installation the gasket sealing surfaces must be free from sealer and gasket materials, clean them properly. Place the new side gaskets to the engine block, be sure that the bolt holes align then spread a thin layer of sealer on the gaskets. Set the front and rear seals into the sealer and jam the ends of these to the side gaskets ends. Place the pan in the required position and fit all bolts loosely up to the position when they can be tightened using fingers, and then tighten the end bolts. Lower the engine onto its mounts and install the through bolts tightening them to the standard torque. Work in reverse, adding the proper grade and amount of oil, turn on the engine, and you are required to check if there is any leakage. If the engine has been pulled out from the vehicle, then most of the steps pertaining to above will not come into the picture and the pan will simply bolted and can be lifted off from the engine block in the process discussed earlier, while the installation process will involve cleaning and sealing steps described above.