How to check and replace front wheel bearings on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

In most cases, the front wheel bearings should be checked whenever the front of the vehicle is raised, typically coinciding with brake pad replacement. The vehicle must be supported safely on jackstands and each wheel assessed by spinning it while checking for noise, rolling resistance and freeplay. You should grab the top and bottom of each tire to check for excessive play as you move the wheel in and out on the spindle; if there is any noticeable movement, bearing inspection, repacking with grease or replacement is required. After removing the wheel, remove the brake caliper and hang it out of your way possibly using a wood block between the brake pads for separation. Thereafter pry out dust cap, straighten and remove cotter pin then take off nut lock, nut, and washer from spindle. Slightly pull hub/disc assembly outwardly then push it back to facilitate removal of outer bearing. Then separate hub/disc assembly from spindle using screwdriver skimming seal out of rear side of hub keeping in mind how it was oriented during its installation. Proceed further to remove inner wheel bearing, clean all components thoroughly with solvent before carefully inspecting them for damage on races or bearings themselves. Replace any defective bearing races at a machine shop if necessary making sure that old bearings are not installed on new races. Thereafter pack bearings with high-temperature front wheel bearing grease and apply thin coat to designated spindle areas. Finger dam grease inboard of each bearing race inside the hub to contain excess grease. After this insert grease-packed inner bearing, a new seal then put outer bearing on top. Place washer on spindle followed by spindle nut which should be tightened gently; spin hub while tightening to approximately 20 ft-lbs then loosen 1/4-turn and finally secure snugly by hand using new cotter pin plus nut lock. Next install dust cap; replace brake caliper; re-attach the wheel then check condition of bearings by grabbing top & bottom of the tire. Finally, lower the vehicle.

How to replace the rear Wheel Bearing on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the axleshaft and oil seal, you will first need a bearing puller. Attach the puller to the slide hammer, the bearing can be extracted from the axle housing. After removing the bearing, the recess should be cleaned out. The new bearing can then be installed using a bearing installer or a piece of pipe against the outer bearing race. Ensure that the bearing is tapped in fully and that the numbers are visible from the outer end of the axle housing, and then install a new oil seal before reattaching the axleshaft.

Genuine GMC Sonoma Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Wheel Bearings found

View related parts
GMC Sonoma Rear Wheel Bearing
Part Number: 12479031
$46.59 MSRP: $92.44
You Save: $45.85 (50%)
ADD TO CART
Product Specifications
- Other Name: Bearing,Rear Wheel
- Position: Rear
- Replaces: 09442126, 9442126
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2003 GMC Sonoma | PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 457052
$38.08 MSRP: $66.52
You Save: $28.44 (43%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Inner
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1995 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 457196
$23.79 MSRP: $43.24
You Save: $19.45 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Inner
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2003 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 26053326
$10.10 MSRP: $19.06
You Save: $8.96 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft; Axle Bearing, Bearing, Output Shaft Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 26041515
$27.08 MSRP: $51.10
You Save: $24.02 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft; Inner Pinion Bearing, Output Shaft Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Rear Wheel Bearing
Part Number: 88927028
$25.19 MSRP: $47.53
You Save: $22.34 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Rear Axle Shaft
- Position: Rear
- Replaces: 15595140
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2003 GMC Sonoma | PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Wheel Bearing
Part Number: 14066918
$10.68 MSRP: $20.16
You Save: $9.48 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Wheel Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2003 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 457434
$10.48 MSRP: $27.74
You Save: $17.26 (63%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing,Front Drive Axle Inner Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2003 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 12413045
$228.98 MSRP: $454.33
You Save: $225.35 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Kit,Front Wheel; Hub & Bearing
- Position: Front
- Replaces: 07470607, 19150096, 7470607
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
GMC Sonoma Wheel Hub Kit, Front
Part Number: 7470013
$196.54 MSRP: $599.94
You Save: $403.40 (68%)
ADD TO CART
Product Specifications
- Other Name: Hub Kit,Front Wheel; Hub & Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
- 1991-1992 GMC Sonoma | PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Hub
Part Number: 26041516
$4.46 MSRP: $8.42
You Save: $3.96 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Asm,Front Drive Axle Clutch Shaft; Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
- 1995 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L
View related parts
GMC Sonoma Rear Wheel Bearing
Part Number: 12471606
$8.03 MSRP: $14.39
You Save: $6.36 (45%)
Product Specifications
- Other Name: Bearing,Rear Axle Shaft
- Position: Rear
- Replaces: 09428573, 07451785, 9428573, 7451785
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2004 GMC Sonoma | 4 DOOR, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Front Wheel Bearing
Part Number: 26029615
Product Specifications
- Other Name: Bearing,Front Drive Axle Clutch Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 GMC Sonoma | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
GMC Sonoma Wheel Hub Kit, Front
Part Number: 7470005
Product Specifications
- Other Name: Hub Kit,Front Wheel; Front Hub, Front Hub & Bearing, Hub, Hub & Bearing
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 GMC Sonoma | PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L

GMC Sonoma Wheel Bearing

The Wheel Bearing of GMC Sonoma vehicles is a fundamental component connected with the vehicle's wheels, which helps in enhancing the performance as well as durability of the vehicle. Speaking of hub and bearing arrangements, there are 3 of them and the most well-known type is the unit assembly where ABS sensor is integrated. Worn bearings will cause noise, vibration, and in some cases, can actually come off the wheel. For checking problems turn the wheel, examine hub, and for play use dial indicator. Tapered roller bearings with remote grease supply that can be lubricated with different kinds of grease thus, need to be inspected keenly and appropriately greased. In general, it is crucial to keep and, if necessary, change wheel bearings to increase compliance with performance requirements for GMC Sonoma cars.

Each OEM GMC Sonoma Wheel Bearing we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

GMC Sonoma Wheel Bearing Parts Questions & Experts Answers

Front Wheel Bearing
457052
Q: How to check and replace front wheel bearings on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: In most cases, the front wheel bearings should be checked whenever the front of the vehicle is raised, typically coinciding with brake pad replacement. The vehicle must be supported safely on jackstands and each wheel assessed by spinning it while checking for noise, rolling resistance and freeplay. You should grab the top and bottom of each tire to check for excessive play as you move the wheel in and out on the spindle; if there is any noticeable movement, bearing inspection, repacking with grease or replacement is required. After removing the wheel, remove the brake caliper and hang it out of your way possibly using a wood block between the brake pads for separation. Thereafter pry out dust cap, straighten and remove cotter pin then take off nut lock, nut, and washer from spindle. Slightly pull hub/disc assembly outwardly then push it back to facilitate removal of outer bearing. Then separate hub/disc assembly from spindle using screwdriver skimming seal out of rear side of hub keeping in mind how it was oriented during its installation. Proceed further to remove inner wheel bearing, clean all components thoroughly with solvent before carefully inspecting them for damage on races or bearings themselves. Replace any defective bearing races at a machine shop if necessary making sure that old bearings are not installed on new races. Thereafter pack bearings with high-temperature front wheel bearing grease and apply thin coat to designated spindle areas. Finger dam grease inboard of each bearing race inside the hub to contain excess grease. After this insert grease-packed inner bearing, a new seal then put outer bearing on top. Place washer on spindle followed by spindle nut which should be tightened gently; spin hub while tightening to approximately 20 ft-lbs then loosen 1/4-turn and finally secure snugly by hand using new cotter pin plus nut lock. Next install dust cap; replace brake caliper; re-attach the wheel then check condition of bearings by grabbing top & bottom of the tire. Finally, lower the vehicle.
Rear Wheel Bearing
88927028
Q: How to replace the rear Wheel Bearing on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the axleshaft and oil seal, you will first need a bearing puller. Attach the puller to the slide hammer, the bearing can be extracted from the axle housing. After removing the bearing, the recess should be cleaned out. The new bearing can then be installed using a bearing installer or a piece of pipe against the outer bearing race. Ensure that the bearing is tapped in fully and that the numbers are visible from the outer end of the axle housing, and then install a new oil seal before reattaching the axleshaft.