My Garage
My Account
Cart
Genuine GMC Jimmy Water Pump
H2O Pump- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
9 Water Pumps found
GMC Jimmy Engine Coolant Pump Kit
Part Number: 89060527$216.27 MSRP: $429.11You Save: $212.84 (50%)Ships in 1-3 Business Days
GMC Jimmy Water Pump Kit
Part Number: 19417097$127.28 MSRP: $252.53You Save: $125.25 (50%)Ships in 1-2 Business Days
GMC Jimmy Pump Kit, Wat
Part Number: 12708487$278.88 MSRP: $526.18You Save: $247.30 (47%)Ships in 1-2 Business Days
GMC Jimmy Pump Kit, Wat
Part Number: 12708488$212.72 MSRP: $422.06You Save: $209.34 (50%)Ships in 1-3 Business Days
GMC Jimmy Engine Coolant Pump Kit
Part Number: 12491038$134.60 MSRP: $230.74You Save: $96.14 (42%)Ships in 1-2 Business Days
GMC Jimmy Water Pump
The Water Pump in GMC Jimmy cars is a critical component that transfers water and anti-freeze solution from the radiator to the engine where it gets hot as a result of combustion. Again, nearly all Jimmy models include a belt-driven water pump as a standard component; however, upgraded ice vehicles may have electric ones. Such pumps can equipped with the aluminum castings with a rotating shaft, which is based on the pulley with the impeller formed to move the coolant. The symptoms that are likely to indicate that the car's water pump is failing are leaks, noise coming from the bearings and cases where the engine overheats. For high-revving engines and race prepared engines there are high performance water pumps, these have better coolant flow than standard designs and less amperage draw. As we have already discussed electric pumps can also be used to get rid of parasitic power loss and for better control of circulation of coolant.
Each OEM GMC Jimmy Water Pump we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
GMC Jimmy Water Pump Parts Questions & Experts Answers
- Q: How do I remove the water pump on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?A: To remove the water pump, start by disconnecting the battery cable from the negative battery terminal. Then, drain the coolant and remove the upper radiator shroud and fan/clutch assembly. Next, take off the serpentine belt and water pump pulley. Disconnect the radiator hose and heater hose from the water pump. Unbolt the water pump, tapping it with a soft-lace hammer if necessary to break the gasket seal. Inspect the pump's impeller blades for corrosion and replace the pump if needed. To install the new water pump, clean the sealing surfaces of all gasket material on both the pump and block. Apply a thin layer of RTV sealant to both sides of the new gasket and install it on the water pump. Place the water pump in position and tighten the bolts to the specified torque. The rest of the installation procedure is the reverse of the removal. Finally, add coolant to the specified level, start the engine, and check for leaks in the water pump and hoses. Bleed the cooling system of any air.
- Q: What are the three quick-checks to determine if the water pump is functioning properly while it is still installed on the engine for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?A: Water pump failure can cause overheating and engine damage. There are three quick-checks to determine if the water pump is functioning properly. If any of these checks indicate problems, immediate replacement is necessary. One way to check is to inspect the weep hole for coolant leakage. Another way is to listen for a high-pitched squealing sound from the water pump. Excessive bearing wear can be identified by moving the water pump pulley. It is important to note that a water pump can be faulty even without howling or leaking water. To check for this, the pump must be removed.
