How do you remove the rear stabilizer bar and link on Chevrolet Traverse?

To remove and install a sway bar kit on a vehicle, begin by loosening the rear wheel lug nuts and raising the rear of the vehicle on jackstands. Block the front wheels and remove the back wheels. Next, remove the spare tire and the left and right side sway bar link-to-sway bar kit nuts, along with the washers and bushings.

How do you remove the front stabilizer bar and link on Chevrolet Traverse?

To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle on jackstands. Remove the front wheels and unbolt the intermediate driveaxle shaft bracket from the subframe. If it's an all-wheel drive model, remove the rear driveshaft. Detach the sway bar link from the strut or bar by holding the ballstud with a wrench and unscrewing the nut. Then, detach the tie-rod ends from the steering knuckle. Support the rear of the subframe with floor jacks and remove the subframe rear reinforcement bolts. Loosen the subframe front reinforcement bolts and the subframe front mounting bolts. Loosen the subframe rear mounting bolts and slowly lower the floor jacks while backing out the rear bolts. Remove the bolts and detach the sway bar kit bushing retainer. Inspect and replace the bushings if necessary. Clean the bushing area of the sway bar kit with a wire brush and lubricate the new bushings with vegetable oil. For installation, reverse the removal steps and tighten the fasteners to the specified torque values. Raise the subframe using floor jacks and tighten the mounting bolts in the proper order. Finally, install the wheels and tighten the lug nuts to the specified torque.

Genuine Chevrolet Traverse Sway Bar Link

Stabilizer Sway Bar Link

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Sway Bar Links found

View related parts
Chevrolet Traverse Link Assembly, Front Stabilizer Shaft
Part Number: 20905104
$41.71 MSRP: $82.75
You Save: $41.04 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: LINK, Stabilizer Shaft; Link, Stabilizer Link
- Position: Front
- Replaces: 15127978, 25981951
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2017 Chevrolet Traverse | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
Chevrolet Traverse Link Assembly, Front Stabilizer Shaft
Part Number: 84108681
$26.97 MSRP: $50.89
You Save: $23.92 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly, Front Stab Shf; Link, Stabilizer Link
- Position: Front
- Replaces: 23384551
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Traverse | 1LT/2LT EXTENDED 4 DOOR SUV, 1LZ/2LZ EXTENDED 4 DOOR SUV, LS EXTENDED 4 DOOR SUV, LT EXTENDED 4 DOOR SUV, LTZ EXTENDED 4 DOOR SUV | 4 Cyl 2.0L, 6 Cyl 3.6L
View related parts
Chevrolet Traverse Link Assembly, Rear Stabilizer Shaft
Part Number: 15129234
$43.52 MSRP: $82.12
You Save: $38.60 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: LINK, Stabilizer Shaft; Link, Stabilizer Link
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2017 Chevrolet Traverse | SPORT UTILITY VEHICLE 2WD, SPORT UTILITY VEHICLE 4WD, SPORT UTILITY VEHICLE AWD | 6 Cyl 3.6L
View related parts
Chevrolet Traverse LINK ASM-RR STAB SHF
Part Number: 87848812
$25.66 MSRP: $46.03
You Save: $20.37 (45%)
ADD TO CART
Product Specifications
- Other Name: Link, Stabilizer Link
- Replaces: 22992986, 84378279, 84012690, 84810706, 84966811
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Traverse | 1LT/2LT EXTENDED 4 DOOR SUV, 1LZ/2LZ EXTENDED 4 DOOR SUV, LS 4 DOOR APV EXTENDED, LS EXTENDED 4 DOOR SUV, LT 4 DOOR APV EXTENDED, LT EXTENDED 4 DOOR SUV, LTZ EXTENDED 4 DOOR SUV, PREM 4 DOOR APV EXTENDED, Z71 4 DOOR APV EXTENDED | 4 Cyl 2.0L, 4 Cyl 2.5L, 6 Cyl 3.6L
View related parts
Chevrolet Traverse LINK ASM-FRT STAB SHF
Part Number: 26428441
$9.78 MSRP: $17.54
You Save: $7.76 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Traverse | LS 4 DOOR APV EXTENDED , LT 4 DOOR APV EXTENDED , PREM 4 DOOR APV EXTENDED, Z71 4 DOOR APV EXTENDED | 4 Cyl 2.5L
View related parts
Chevrolet Traverse Link Assembly, Rear Stab Shf
Part Number: 84966811
$24.39 MSRP: $46.03
You Save: $21.64 (48%)
ADD TO CART
Product Specifications
- Other Name: Link, Stabilizer Link
- Position: Rear
- Replaced by: 87848812
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Traverse | 1LT/2LT EXTENDED 4 DOOR SUV, 1LZ/2LZ EXTENDED 4 DOOR SUV, LS EXTENDED 4 DOOR SUV, LT EXTENDED 4 DOOR SUV, LTZ EXTENDED 4 DOOR SUV | 4 Cyl 2.0L, 6 Cyl 3.6L

Chevrolet Traverse Sway Bar Link

In essence, the Sway Bar Link in Chevrolet Traverse cars is responsible for controlling the roll of the body through linking two different assemblies of wheel. This component links the sway bar to the control arm and its task is to oppose the motion of the inside tire while the car is turning and thus lessen body roll. Through achieving equal weight transmission and control of a car's handling on curves, the sway bar link helps in increasing stability of a vehicle. Further, the sway bar link helps has the responsibility of the proper transfer of motion between the control arm and the sway bar hence ensuring proper working of the suspension system.

Each OEM Chevrolet Traverse Sway Bar Link we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet Traverse Sway Bar Link Parts Questions & Experts Answers

Link Assembly, Rear Stabilizer Shaft
15129234
Q: How do you remove the rear stabilizer bar and link on Chevrolet Traverse?
A: To remove and install a sway bar kit on a vehicle, begin by loosening the rear wheel lug nuts and raising the rear of the vehicle on jackstands. Block the front wheels and remove the back wheels. Next, remove the spare tire and the left and right side sway bar link-to-sway bar kit nuts, along with the washers and bushings.
Link Assembly, Front Stabilizer Shaft
20905104
Q: How do you remove the front stabilizer bar and link on Chevrolet Traverse?
A: To remove the sway bar kit, start by loosening the front wheel lug nuts and raising the front of the vehicle on jackstands. Remove the front wheels and unbolt the intermediate driveaxle shaft bracket from the subframe. If it's an all-wheel drive model, remove the rear driveshaft. Detach the sway bar link from the strut or bar by holding the ballstud with a wrench and unscrewing the nut. Then, detach the tie-rod ends from the Steering Knuckle. Support the rear of the subframe with floor jacks and remove the subframe rear reinforcement bolts. Loosen the subframe front reinforcement bolts and the subframe front mounting bolts. Loosen the subframe rear mounting bolts and slowly lower the floor jacks while backing out the rear bolts. Remove the bolts and detach the sway bar kit bushing retainer. Inspect and replace the bushings if necessary. Clean the bushing area of the sway bar kit with a wire brush and lubricate the new bushings with vegetable oil. For installation, reverse the removal steps and tighten the fasteners to the specified torque values. Raise the subframe using floor jacks and tighten the mounting bolts in the proper order. Finally, install the wheels and tighten the lug nuts to the specified torque.