What are the three quick-checks to determine if the water pump is functioning properly while it is still installed on the engine for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

Water pump failure can cause overheating and engine damage. There are three quick-checks to determine if the water pump is functioning properly. If any of these checks indicate problems, immediate replacement is necessary. One way to check is to inspect the weep hole for coolant leakage. Another way is to listen for a high-pitched squealing sound from the water pump. Excessive bearing wear can be identified by moving the water pump pulley. It is important to note that a water pump can be faulty even without howling or leaking water. To check for this, the pump must be removed.

How do I remove the water pump on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To remove the water pump, start by disconnecting the battery cable from the negative battery terminal. Then, drain the coolant and remove the upper radiator shroud and fan/clutch assembly. Next, take off the serpentine belt and water pump pulley. Disconnect the radiator hose and heater hose from the water pump. Unbolt the water pump, tapping it with a soft-lace hammer if necessary to break the gasket seal. Inspect the pump's impeller blades for corrosion and replace the pump if needed. To install the new water pump, clean the sealing surfaces of all gasket material on both the pump and block. Apply a thin layer of RTV sealant to both sides of the new gasket and install it on the water pump. Place the water pump in position and tighten the bolts to the specified torque. The rest of the installation procedure is the reverse of the removal. Finally, add coolant to the specified level, start the engine, and check for leaks in the water pump and hoses. Bleed the cooling system of any air.

Genuine Chevrolet S10 Water Pump

H2O Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Water Pumps found

View related parts
Chevrolet S10 Engine Coolant Pump Kit
Part Number: 89060527
$216.27 MSRP: $429.11
You Save: $212.84 (50%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit,Water; Water Pump, Water Pump Assembly
- Replaces: 12528917, 89017748, 12532528
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 Water Pump Kit
Part Number: 19417097
$127.28 MSRP: $252.53
You Save: $125.25 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit,Wat; Water Pump, Water Pump Assembly
- Replaces: 19201601, 88894005, 12532531, 12532529, 12369487
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1995 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Engine Coolant Pump Kit
Part Number: 19309748
$57.43 MSRP: $103.02
You Save: $45.59 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit,Water ; Pump Kit, Engine Coolant
- Replaces: 88926166
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | PICKUP | 4 Cyl 2.5L
View related parts
Chevrolet S10 Engine Coolant Pump Kit
Part Number: 12491038
$134.60 MSRP: $230.74
You Save: $96.14 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit,Water ; Pump Kit, Engine Coolant; Water Pump, Water Pump Assembly
- Replaces: 12458920, 10181327
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1993 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 2.5L
View related parts
Chevrolet S10 Engine Coolant Pump Kit
Part Number: 12507784
Product Specifications
- Other Name: Pump Kit,Water ; Pump Kit, Engine Coolant; Water Pump, Water Pump Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 2.5L
View related parts
Chevrolet S10 Water Pump Assembly
Part Number: 10089659
Product Specifications
- Other Name: Pump Asm,Water; Water Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Chevrolet S10 | 2 DOOR, PICKUP | 6 Cyl 2.8L
View related parts
Chevrolet S10 Engine Coolant Pump Kit
Part Number: 12462265
Product Specifications
- Other Name: Pump Kit,Water; Water Pump, Water Pump Assembly
- Replaces: 12363169, 12518443
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2003 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex
View related parts
Chevrolet S10 Water Pump Kit
Part Number: 12482690
Product Specifications
- Other Name: Pump Kit,Water; Water Pump
- Replaces: 10120943
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 6 Cyl 2.8L
View related parts
Chevrolet S10 Water Pump Assembly
Part Number: 94105354
Product Specifications
- Other Name: Pump Asm,Water ; Pump, Engine Coolant; Water Pump
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 2.2L Diesel

Chevrolet S10 Water Pump

The Water Pump in Chevrolet S10 vehicles helps pump the coolant from the radiator to the engine so as to draw off and dissipate heat produced through combustion. In standard configuration, most S10 Water Pumps are of the auxiliary system which means they are powered by a belt from the crankshaft although new models come with electric pumps. These pumps normally come with aluminum castings with a running shaft, belt installed pulley and impeller to circulate the coolant in the system. The signs of the failing Water Pump are thus, coolant leaks, noises produced due to worn bearings and finally high engine temperature. High Performance Water Pump can offer numerous upgrades for high performing engines regarding to coolant flow and less power draw than standard pumps. Electric Water Pumps are also available that have advantages like flow of coolant independently of the engine, cooling after the shutdown of the engine and the possible remote mounting whilst occupying less space.

Each OEM Chevrolet S10 Water Pump we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Water Pump Parts Questions & Experts Answers

Engine Coolant Pump Kit
89060527
Q: What are the three quick-checks to determine if the water pump is functioning properly while it is still installed on the engine for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: Water pump failure can cause overheating and engine damage. There are three quick-checks to determine if the water pump is functioning properly. If any of these checks indicate problems, immediate replacement is necessary. One way to check is to inspect the weep hole for coolant leakage. Another way is to listen for a high-pitched squealing sound from the water pump. Excessive bearing wear can be identified by moving the water pump pulley. It is important to note that a water pump can be faulty even without howling or leaking water. To check for this, the pump must be removed.
Water Pump Kit
19417097
Q: How do I remove the water pump on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To remove the water pump, start by disconnecting the battery cable from the negative battery terminal. Then, drain the coolant and remove the upper radiator shroud and fan/clutch assembly. Next, take off the serpentine belt and water pump pulley. Disconnect the radiator hose and heater hose from the water pump. Unbolt the water pump, tapping it with a soft-lace hammer if necessary to break the gasket seal. Inspect the pump's impeller blades for corrosion and replace the pump if needed. To install the new water pump, clean the sealing surfaces of all gasket material on both the pump and block. Apply a thin layer of RTV sealant to both sides of the new gasket and install it on the water pump. Place the water pump in position and tighten the bolts to the specified torque. The rest of the installation procedure is the reverse of the removal. Finally, add coolant to the specified level, start the engine, and check for leaks in the water pump and hoses. Bleed the cooling system of any air.