My Garage
My Account
Cart
Genuine Chevrolet S10 Timing Cover
Engine Timing Cover- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
11 Timing Covers found
Chevrolet S10 Cover Assembly, Engine Front
Part Number: 93445880$79.88 MSRP: $139.02You Save: $59.14 (43%)
Chevrolet S10 Cover Kit,Engine Front
Part Number: 89017259$95.87 MSRP: $150.84You Save: $54.97 (37%)Ships in 1-2 Business Days
Chevrolet S10 Timing Cover
The Timing Cover of Chevrolet S10 vehicles is an alloy casting that acts as a shroud to the timing belt/chain which prevents debris from damaging an important component of the car's engine. Usual materials used in the manufacture of these covers are aluminum and steel, the more refined materials like the plastic ones often contain gasket that improves the overall protection of timing belt. Depending on the years of the manufacture of the S10 model, different types of timing covers may be installed in the car, but whatever type is used it is aimed at protecting the timing system of the vehicle against damage. Replacement of a timing cover that has been worn or damaged and carrying out consistent maintenance are vital issues that help keep the car in good condition on the road.
Each OEM Chevrolet S10 Timing Cover we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.
Chevrolet S10 Timing Cover Parts Questions & Experts Answers
- Q: How do I remove and install the timing chain cover,Timing Chain and Sprocket on 2.2L four cylinder engine on Chevrolet S10?A: Begin by removing the cover, then isolate it from the negative battery cable. After that, remove fan shroud upper part, drive belt, fan/clutch assembly, water pump pulley, crankshaft pulley and hub. Remove the drive belt tensioner bracket and Timing Cover-to-engine block bolts next. Utilize a gasket scraper to erase any old gasket material and clean any of the sealing surfaces. To remove the timing chain; temporarily install crankshaft pulley hub and bolt; rotate crankshaft to align timing marks on crankshaft and camshaft sprockets; push back timing chain tensioner plunger and insert pin to retain plunger; using prybar holding engine while removing camshaft bolt; carefully prying camshaft sprocket off. Check for damage or wearout on timing chain and sprockets before replacing if necessary. Mesh new timing chains with camshafts; put them into engagement with crankshafts at their sprocket's teeth; aligning timing marks; installing tightening camshaft sprocket bolt; releasing tensioner; lubricating chain/sprocket; rotating engine to check alignment of timing marks; applying RTV sealant to oil pan sealing surface; finally securing front cover using new rubber seal.
- Q: How to remove and install the timing chain cover,Timing Chain and Sprocket on 4.3L V6 engine on Chevrolet S10?A: Disconnecting the negative battery cable is the first step in removal and installation of the Timing Cover. To remove, you will have to remove upper and lower fan shrouds, drive belt, cooling fan and water pump. The number four piston must be positioned at TDC on the compression stroke, then remove the drive belt pulley and crankshaft damper. If applicable, don't forget to take out the crankshaft position sensor and wiring harness nut. Loosen front Oil Pan nuts before removing cover bolts when separating Timing Cover from block and breaking gasket seal if necessary. Note that for some engines, the front cover may be made of composite material and should be replaced rather than resealed. Just inside the front cover, pull off crankshaft position sensor reluctor ring which is attached to a camshaft sprocket and chain assembly. For an old gasket material use a gasket scraper to scrape it off; cleaning lacquer thinner or acetone should be wiped over sealing surfaces of engine cover and block; inspecting flange condition of a cover is recommended. Make sure that when installing a Woodruff key line up coincides with both crankshaft sprocket's as well as balance shaft gears'. Use clean engine oil to lubricate the chain; put Loctite on camshaft sprocket bolt threads before installing them tightly or tighten them after installing using Loctite. Apply RTV sealant in U-shaped channel on bottom side of the cover check oil pan-to-block joints; also check whether there are any leaks between housing halves in place where they meet with each other in front of timing chain area that is why you need to apply RTV sealant between them too. Thin layer of RTV sealant should be spread over both sides of new gasket so that it can be positioned on engine block by dowel pins thus holding it firmly in place. Finally install Timing Cover and tighten bolts taking into account whether it is necessary to remove or pry down oil pan for access. Lastly, apply moly-base grease or clean engine oil onto the vibration damper hub's oil seal contact surface, put the damper on the crankshaft, and proceed with other remaining installation steps including using new O-ring for crankshaft position sensor.
Related Chevrolet S10 Parts
Chevrolet S10 Rocker Arm
Chevrolet S10 Camshaft
Chevrolet S10 Rocker Shaft Spring Kit
Chevrolet S10 Cylinder Head
Chevrolet S10 Intake Valve
Chevrolet S10 Exhaust Valve
Browse by Year
2004 Timing Cover 2003 Timing Cover 2002 Timing Cover 2001 Timing Cover 2000 Timing Cover 1999 Timing Cover 1998 Timing Cover 1997 Timing Cover 1996 Timing Cover 1995 Timing Cover 1994 Timing Cover 1993 Timing Cover 1992 Timing Cover 1991 Timing Cover 1990 Timing Cover 1989 Timing Cover 1988 Timing Cover 1987 Timing Cover 1986 Timing Cover 1985 Timing Cover