How to check and replace Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Intake Manifold Temperature Sensor,Knock Sensor,Oxygen Sensor,Vehicle Speed Sensor,Neutral Safety Switch,MAP Sensor and Throttle Position Sensor on Chevrolet S10?

Various engine sensors and components have checking procedures,the engine coolant temperature (ECT) sensor is a thermistor that changes resistance with temperature, and a failure in the circuit can cause trouble codes. The resistance should be measured when cold and warm while ensuring reference voltage from PCM is around 5.0 volts for the verification. Manifold Absolute Pressure (MAP) Sensor monitors changes in intake manifold pressure then varies its voltage output accordingly. Look at the reference voltage and signal voltage with the ignition on and engine off, and observe voltage changes as the engine's vacuum changes. Intake Air Temperature (IAT) Sensor acts as a thermistor where you can measure its resistance at different temperatures to make sure it changes as expected. Also, use a scan tool to monitor the IAT sensor for performance. The oxygen sensor in exhaust detects oxygen content which you can check its millivolt signal while warming up your engine. Check whether the oxygen sensor heater has correct voltage or not. Vehicle Speed Sensor (VSS) provides speed data to PCM which can be checked for reference voltage. Depending on the type of engine, Camshaft Sensor and Crankshaft Sensor should be checked for resistance and proper signal output. Finally, Knock Sensors detect engine knock which should be checked for reference voltage and resistance. If any component fails these checks, replacement may be necessary.

Genuine Chevrolet S10 Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Crankshaft Position Sensors found

View related parts
Chevrolet S10 Sensor,Crankshaft Position
Part Number: 12596851
$73.79 MSRP: $153.20
You Save: $79.41 (52%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Replaces: 10456607, 10456532, 12562910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 Sensor,Crankshaft Position
Part Number: 10456555
$21.99 MSRP: $70.71
You Save: $48.72 (69%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Replaces: 10456043
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chevrolet S10 | PICKUP | 4 Cyl 2.2L
View related parts
Chevrolet S10 SENSOR ASM,CM/SHF POSN (KIT)
Part Number: 19417445
$54.45 MSRP: $102.74
You Save: $48.29 (47%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Replaces: 10490645, 10485432
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 Sensor Assembly, Knock
Part Number: 21024981
$30.98 MSRP: $58.47
You Save: $27.49 (48%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Knock Sensor
- Replaces: 21024729
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 Sensor,Knock
Part Number: 10456287
$26.49 MSRP: $85.22
You Save: $58.73 (69%)
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Control Module, ESC Sensor, Knock Sensor, Sensor
- Replaces: 10456017
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 6 Cyl 2.8L
View related parts
Chevrolet S10 Sensor,Crankshaft Position
Part Number: 10456614
$56.75 MSRP: $205.92
You Save: $149.17 (73%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor)
- Replaces: 10456134
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet S10 | PICKUP | 4 Cyl 2.2L
View related parts
Chevrolet S10 Sensor,Crankshaft Position
Part Number: 24575636
Product Specifications
- Other Name: SENSOR, Distributor (also Knock Sensor); Crankshaft Position Sensor, Crankshaft Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2003 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex

Chevrolet S10 Crankshaft Position Sensor

Crankshaft Position Sensor in Chevrolet S10 vehicles is an important electronic part as it provides input signals of phase of the engine to the management system of the vehicle. This sensor helps in controlling of fuel injection and ignition timing and some other aspect of the engine. The sensor, most often, is fixed to the main crank pulley, flywheel, camshaft, or crankshaft itself; the types of the sensor are inductive, their Hall Effect, magnetoresistive, and optical sensors. Precise information is vital for proper engine operation; thus, the sensor failure can cause starting problems and engine cut-outs. In general, the Crankshaft Position Sensor plays a very significant role in the efficiency and smooth running of Chevrolet S10 vehicles' engines.

Each OEM Chevrolet S10 Crankshaft Position Sensor we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Crankshaft Position Sensor Parts Questions & Experts Answers

Sensor,Crankshaft Position
24575636
Q: How to check and replace Camshaft Position Sensor,Coolant Temperature Sensor,Crankshaft Position Sensor,Intake Manifold Temperature Sensor,Knock Sensor,Oxygen Sensor,Vehicle Speed Sensor,Neutral Safety Switch,MAP Sensor and Throttle Position Sensor on Chevrolet S10?
A: Various engine sensors and components have checking procedures,the engine coolant temperature (ECT) sensor is a thermistor that changes resistance with temperature, and a failure in the circuit can cause trouble codes. The resistance should be measured when cold and warm while ensuring reference voltage from PCM is around 5.0 volts for the verification. Manifold Absolute Pressure (MAP) Sensor monitors changes in intake manifold pressure then varies its voltage output accordingly. Look at the reference voltage and signal voltage with the ignition on and engine off, and observe voltage changes as the engine's vacuum changes. Intake Air Temperature (IAT) Sensor acts as a thermistor where you can measure its resistance at different temperatures to make sure it changes as expected. Also, use a scan tool to monitor the IAT sensor for performance. The oxygen sensor in exhaust detects oxygen content which you can check its millivolt signal while warming up your engine. Check whether the oxygen sensor heater has correct voltage or not. Vehicle Speed Sensor (VSS) provides speed data to PCM which can be checked for reference voltage. Depending on the type of engine, Camshaft Sensor and Crankshaft Sensor should be checked for resistance and proper signal output. Finally, Knock Sensors detect engine knock which should be checked for reference voltage and resistance. If any component fails these checks, replacement may be necessary.