How to inspect and replace flexible brake hoses for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the above defects are found, the hose should be replaced with a new one. To replace the hose, start by cleaning any dirt away from the ends of the hose and disconnecting the brake line from the hose fitting, being careful not to bend the frame bracket or line. If necessary, soak the connections with penetrating oil. Remove the U-clip from the female fitting at the bracket and remove the hose from the bracket. Disconnect the hose from the caliper, discarding the copper washers on either side of the fitting. Attach the new brake hose to the caliper using new copper washers. Pass the female fitting through the frame or frame bracket, installing it with the least amount of twist in the hose. Install the U-clip in the female fitting at the frame bracket. Attach the brake line to the hose fitting using a back-up wrench on the fitting. Carefully check to ensure that the suspension or steering components do not make contact with the hose, and have an assistant push down on the vehicle and turn the steering wheel lock-to-lock during inspection. Afterward, bleed the brake system. When replacing brake lines, always use the correct parts and avoid using copper tubing. Purchase steel brake lines, preferably prefabricated ones with the tube ends already flared and fittings installed. Ensure that the new line is well supported in the brackets and has plenty of clearance between moving or hot components. After installation, check the master cylinder fluid level and add fluid as necessary. Finally, bleed the brake system and test the brakes carefully before placing the vehicle into normal operation.

Genuine Chevrolet S10 Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

64 Brake Lines found

View related parts
Chevrolet S10 Hose Asm,Rear Brake
Part Number: 19366755
$35.36 MSRP: $66.72
You Save: $31.36 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE ASM,RR BRK; Brake Hose, Flex Hose
- Position: Rear
- Replaces: 22113466, 17989773
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Pipe,Brake (Bulk Tubing 5/16" 8Mm)
Part Number: 12541500
$33.77 MSRP: $53.13
You Save: $19.36 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Standard Parts; Cooler Line, Line, Oil Cooler Tube
- Replaces: 01324714, 1324714
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1997 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Hose Asm,Rear Brake
Part Number: 19169863
$14.90 MSRP: $26.72
You Save: $11.82 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose
- Position: Rear
- Replaces: 09767001, 18031947, 9767001
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Hose Asm,Front Brake
Part Number: 19173227
$18.58 MSRP: $33.33
You Save: $14.75 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose
- Position: Front
- Replaces: 09768949, 9768949, 18031967
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Hose Asm,Front Brake
Part Number: 19173207
$14.81 MSRP: $26.56
You Save: $11.75 (45%)
ADD TO CART
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose
- Position: Front
- Replaces: 9767269, 09767269, 18031946
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE ASM FRT BRK
Part Number: 15715408
$21.59 MSRP: $25.16
You Save: $3.57 (15%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet S10 | PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 Pipe Assembly, Brake Pressure Mod Valve Rear Brake
Part Number: 15051173
$55.86 MSRP: $100.20
You Save: $44.34 (45%)
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 Hose Asm,Front Brake
Part Number: 19173228
$18.58 MSRP: $33.33
You Save: $14.75 (45%)
Product Specifications
- Other Name: HOSE, Hydraulic Brake; Brake Hose, Flex Hose
- Position: Front
- Replaces: 09768950, 9768950, 18031968
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1985 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L
View related parts
Chevrolet S10 HOSE ASM,RR BRK
Part Number: 19366728
$34.25 MSRP: $61.44
You Save: $27.19 (45%)
Product Specifications
- Other Name: Brake Hose, Flex Hose
- Replaces: 22163464
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE, Vacuum Power Brake
Part Number: 10083128
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | PICKUP | 4 Cyl 2.5L
View related parts
Chevrolet S10 PIPE
Part Number: 15158214
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE ASM FRT BRK COMB VLV
Part Number: 15614075
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1995 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Pipe Assembly, Rear Brk Frt
Part Number: 15638427
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1991 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Pipe Assembly, Front Brake
Part Number: 15689561
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet S10 | PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 Pipe Assembly, Front Brake
Part Number: 15715402
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet S10 | PICKUP | 4 Cyl 2.2L
View related parts
Chevrolet S10 PIPE, Hydraulic Brake
Part Number: 15715406
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet S10 | PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE, Hydraulic Brake
Part Number: 15715420
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet S10 | PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE
Part Number: 15722016
Product Specifications
- Other Name: PIPE, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Chevrolet S10 | ELECTRIC, PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE, Hydraulic Brake
Part Number: 15953358
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1994 Chevrolet S10 | 2 DOOR, 4 DOOR | 4 Cyl 2.2L, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 PIPE, Hydraulic Brake
Part Number: 15979486
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Chevrolet S10 | PICKUP | 4 Cyl 2.2L, 6 Cyl 4.3L

| Page 1 of 4 |Next >

1-20 of 64 Results

Chevrolet S10 Brake Line

So, now coming to the component, the Chevrolet S10 Brake Line is as crucial as other components of hydraulic brake system which links the master cylinder directly to the brake caliper pistons to supply the brake fluid. Brake line used metal, which corrodes and also subjected to impact so easily causing the fluid leak and finally loss of hydraulic pressure. Other regular damages include physical breakage and internal wear of the brake hoses that directly impact the vehicle's braking system. When it comes to replacement solutions, the pre-bend brake line kits and the direct replacement brake hoses can be used and they are easy to use as well as they do not corrode easily. Switching from the rubber type to the steel braided hose can also give a much better feel, especially in cases of spirited driving.

Each OEM Chevrolet S10 Brake Line we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Brake Line Parts Questions & Experts Answers

Hose Asm,Rear Brake
19366755
Q: How to inspect and replace flexible brake hoses for Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: About every six months, it is important to inspect the flexible hoses that connect the steel brake lines with the front and rear brake assemblies for any cracks, chafing, leaks, blisters, or other damage. This inspection should be done with the vehicle raised and securely placed on jackstands, using a light and mirror for a thorough check. If any of the above defects are found, the hose should be replaced with a new one. To replace the hose, start by cleaning any dirt away from the ends of the hose and disconnecting the brake line from the hose fitting, being careful not to bend the frame bracket or line. If necessary, soak the connections with penetrating oil. Remove the U-clip from the female fitting at the bracket and remove the hose from the bracket. Disconnect the hose from the caliper, discarding the copper washers on either side of the fitting. Attach the new brake hose to the caliper using new copper washers. Pass the female fitting through the frame or frame bracket, installing it with the least amount of twist in the hose. Install the U-clip in the female fitting at the frame bracket. Attach the brake line to the hose fitting using a back-up wrench on the fitting. Carefully check to ensure that the suspension or steering components do not make contact with the hose, and have an assistant push down on the vehicle and turn the steering wheel lock-to-lock during inspection. Afterward, bleed the brake system. When replacing brake lines, always use the correct parts and avoid using copper tubing. Purchase steel brake lines, preferably prefabricated ones with the tube ends already flared and fittings installed. Ensure that the new line is well supported in the brackets and has plenty of clearance between moving or hot components. After installation, check the master cylinder fluid level and add fluid as necessary. Finally, bleed the brake system and test the brakes carefully before placing the vehicle into normal operation.