How to Inspect and Replace Brake Disc on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?

To inspect the brakes, begin by loosening wheel lug nuts and raising the front of the vehicle on jack stands. Take off the wheel followed by the brake caliper. While checking for any score marks or damage on disc surfaces, remember that slight scratches and shallow grooves are normal and will not affect the brake operation. Nevertheless, deep grooves of over 0.015-inch deep necessitate disc removal and refinishing at a machine shop. Make sure both sides have been inspected thoroughly. When inspecting a rear disc, reinstall wheel lug nuts with flat side towards disc to hold it in a flat vertical plane during inspection. Washers may be needed under lug nuts to apply pressure to disc. To check for disc runout, place dial indicator about 1/2 inch from outer edge of disc and zero it out. Turn disk around while making sure that reading does not exceed 0.003 inches on indicator gauge; if it does so, then let machine shop refinish disk for you.Additionally don't allow multiple groves on your brake rotors which should be well maintained as long as they don't wear below specified minimum thickness.It is also possible to measure rotor thickness with micrometer.For removal and installation, on 2WD models, the disk is part of the front hub assembly and should be removed and installed according to front wheel bearing maintenance procedure.On 4WD models remove tire; remove caliper , then pull off disk from its mounting onto hub.

Genuine Chevrolet S10 Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Discs found

View related parts
Chevrolet S10 Front Brake Rotor Assembly
Part Number: 19174912
$49.17 MSRP: $88.20
You Save: $39.03 (45%)
Product Specifications
- Other Name: Rotor Asm,Front Brake ; Rotor, Front And Rear Wheel Brake; Brake Rotor, Rotor
- Position: Front
- Replaces: 18027660
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1983-1990 Chevrolet S10 | 2 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Brake Rotor Assembly (W/ Hub)
Part Number: 19211905
Product Specifications
- Other Name: Rotor Asm,Front Brake (W/ Hub) ; Rotor, Front And Rear Wheel Brake; Brake Rotor, Rotor
- Position: Front
- Replaces: 18060219, 15733699, 19152694, 18060691
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet S10 | CREW CAB, ELECTRIC, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Rear Brake Rotor Assembly (W/ Hub)
Part Number: 15733196
Product Specifications
- Other Name: Rotor Assembly, Rear Brake (W/ Hub) ; Rotor, Front And Rear Wheel Brake; Rotor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003 Chevrolet S10 | PICKUP | 6 Cyl 4.3L
View related parts
Chevrolet S10 Rear Brake Rotor
Part Number: 15704667
Product Specifications
- Other Name: Rotor,Rear Brake; Rotor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chevrolet S10 | CREW CAB, PICKUP, PICKUP EXTENDED CAB | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Brake Rotor Assembly
Part Number: 18060242
Product Specifications
- Other Name: Rotor Asm,Front Brake ; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 15606249, 18040476
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1982-1995 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 1.9L, 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.2L Diesel, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L
View related parts
Chevrolet S10 Front Brake Rotor Assembly
Part Number: 19202728
Product Specifications
- Other Name: Rotor Asm,Front Brake ; Rotor, Front And Rear Wheel Brake; Hub & Rotor, Rotor
- Position: Front
- Replaces: 15602574, 19152699, 18060217, 15725351
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2003 Chevrolet S10 | 2 DOOR, 4 DOOR, PICKUP | 4 Cyl 2.2L, 4 Cyl 2.2L Flex, 4 Cyl 2.5L, 6 Cyl 2.8L, 6 Cyl 4.3L

Chevrolet S10 Brake Disc

Brake Disc of Chevrolet S10 is important part of the disc brake system, which is responsible for creating the friction which is needed to stop a vehicle. Often cast from gray iron, such discs may have cooling fins or vanes, which is important for heat exchange and the braking effectiveness. There has been use of different designs of the Brake Discs in the S10 including the solid, vented, drilled, and the slotted kind having their advantages such as efficient cooling and the reduction of noise. The Chevrolet S10 Brake Disc should be well taken care of since problems such as warping, cracking or even rusting affects its performance greatly. Common troubles with Brake Discs can be solved if they are inspected on a regular basis and the pads worn out are changed on time. All in all, the Brake Disc has a significant function involving the design and maintenance for a safe and steady operation of Chevrolet S10 vehicles.

Each OEM Chevrolet S10 Brake Disc we offer is competitively priced and comes with the assurance of the manufacturer's warranty for the part. Furthermore, we guarantee the speedy delivery of your orders right to your doorstep. Our hassle-free return policy is also in place for your peace of mind.

Chevrolet S10 Brake Disc Parts Questions & Experts Answers

Rear Brake Rotor
15704667
Q: How to Inspect and Replace Brake Disc on Chevrolet Blazer,S10,GMC Jimmy and Sonoma?
A: To inspect the brakes, begin by loosening wheel lug nuts and raising the front of the vehicle on jack stands. Take off the wheel followed by the brake caliper. While checking for any score marks or damage on disc surfaces, remember that slight scratches and shallow grooves are normal and will not affect the brake operation. Nevertheless, deep grooves of over 0.015-inch deep necessitate disc removal and refinishing at a machine shop. Make sure both sides have been inspected thoroughly. When inspecting a rear disc, reinstall wheel lug nuts with flat side towards disc to hold it in a flat vertical plane during inspection. Washers may be needed under lug nuts to apply pressure to disc. To check for disc runout, place dial indicator about 1/2 inch from outer edge of disc and zero it out. Turn disk around while making sure that reading does not exceed 0.003 inches on indicator gauge; if it does so, then let machine shop refinish disk for you.Additionally don't allow multiple groves on your brake rotors which should be well maintained as long as they don't wear below specified minimum thickness.It is also possible to measure rotor thickness with micrometer.For removal and installation, on 2WD models, the disk is part of the front hub assembly and should be removed and installed according to front wheel bearing maintenance procedure.On 4WD models remove tire; remove caliper , then pull off disk from its mounting onto hub.